Panasonic AJ-PX5000G, Руководство по эксплуатации

Страница: 166 / 260

– 166 –
Chapter 7 Menu Operations — Menu list
Item Description of settings
[TEXT MEMO (U4)] (Select a function)
Assigns the <TEXT MEMO> button.
For selectable functions and an explanation of functions, refer to “Assigning functions to <USER> buttons”
(page 67).
f
Factory setting: [TEXT MEMO]
(Detection time)
Selects a response to accept when the <TEXT MEMO> button is pressed.
[NORMAL]: Accepts immediately when pressed.
[1sec]: Accepts when pressed and held down for approx. one second.
f
Factory setting: [NORMAL]
[SW MODE]
Item Description of settings
[RET SW] Sets the function when the <RET> button on the lens is pressed.
[INHIBIT]: The <RET> button function is disabled.
[REC CHECK]: Recording check function is enabled. Records can be checked of the last several seconds
recorded.
[CAM RET]: Return video function is enabled. While the <RET> button is pressed, the signal supplied to
the <SDI IN> terminal can be checked on the viewfinder and LCD monitor.
[ASSIST]: Turns the focus assist display [ON]/[OFF].
[D.ZOOM]: Digital zoom function is enabled. Digital zoom can be switched [ON]/[OFF].
[EVF CLR]: Selects whether to display video in the viewfinder in color or in black and white.
[TEXT MEMO]: Text memo function is enabled. A text memo can be recorded to the frame selected when
the button is pressed.
[SHOT MARK]: Shot mark function is enabled. Press to add a shot mark, and press again to remove it.
f
Factory setting: [REC CHECK]
The return video is not displayed correctly when an image signal that differs from the video system of this
camera.
When the main menu → [I/F SETUP] → [GENLOCK] → [GENLOCK] is set to [INT], return video images
may sometimes be skewed slightly in the horizontal direction.
When switching between camera images and return video images, the image on the viewfinder and LCD
monitor may be disrupted for an instant. This is not a malfunction.
[S.BLK LVL] Sets the super black level.
[ − 30], [ − 20], [ − 10], [OFF]
f
Factory setting: [ − 10]
[AUTO KNEE SW] Enables/disables auto knee function and DRS function.
[DRS]: When the <AUTO KNEE> switch is in the <ON> position, DRS function is enabled.
[ON]: When the <AUTO KNEE> switch is in the <ON> position, auto knee function is enabled.
[OFF]: Even if the <AUTO KNEE> switch is in the <ON> position, both auto knee function and DRS
function are not enabled.
f
Factory setting: [ON]
[SHD,ABB SW CTL] Sets whether to automatically adjust black shading when the <AUTO W/B BAL> switch is pressed and
held down on the <ABB> side for two seconds or more.
[ON], [OFF]
f
Factory setting: [OFF]
[COLOR BARS] Selects the color bar to use.
[SMPTE]: Uses the color bar in the SMPTE standard.
[FULL BARS]:
Uses full color bars.
[SPLIT]: Uses SPLIT color bars for SNG (Satellite News Gathering).
[ARIB]: Uses ARIB standard color bars.
f
Factory setting: [SMPTE]
[FOCUS ASSIST] Selects the operation when [ASSIST] (focus assist function) is assigned to the <USER> button or the
<RET> button.
[EXPAND]: Expands the display of the center portion of the video.
[IN RED]: Outlines the contour of the video in red.
f
Factory setting: [EXPAND]
[EXPAND MODE] Selects the method to cancel expanded display when [EXPAND] is selected in [FOCUS ASSIST].
[10SEC]: Cancels in 10 seconds.
[HOLD]: Cancels when the button to which [ASSIST] is assigned is pressed.
[UNTIL REC]: Cancels when recording starts. Expanded display is not available during recording.
f
Factory setting: [10SEC]
Regardless of this setting, expanded display is canceled when the button to which [ASSIST] is assigned is
pressed.
[WFM] Selects the type of waveform to be displayed on the viewfinder screen or LCD monitor when the <USER>
buttons (<USER MAIN>/<USER1>/<USER2>) to which the waveform monitor function is assigned is
pressed.
[WAVE]: Displays as a waveform.
[VECTOR]: Displays as a vector.
[WAVE/VECTOR]: Each time the button is pressed, the display changes in order from no display →
waveform display → vector display → no display.
f
Factory setting: [WAVE]
[WFM DISP] Selects whether to display the waveform monitor on the viewfinder or on the LCD monitor.
[VF]: Displays on the viewfinder.
[LCD]: Displays on the LCD monitor.
[VF/LCD]: Displays on the viewfinder and the LCD monitor.
f
Factory setting: [VF/LCD]