Panasonic AJ-PX380G, Руководство по эксплуатации

Страница: 85 / 229

– 85 –
Chapter 4 Shooting — Dual codec recording
Dual codec recording
Recording in different formats for main recording and sub recording can be performed on the camera.
For sub recording, HD proxy (AVC-LongG 6 format) and SD proxy can be selected according to the [LINE&FREQ] setting.
The file format is MOV that is suitable for nonlinear editing.
For the combination with the main recording, refer to “System modes and recording functions” (page 79).
Dual codec recording setting
Setting menu
When recording proxy data with the camera, set in the main menu → [RECORDING SETUP] → [DUAL CODEC SETTING].
Item Description of settings
[CODEC USAGE] Selects media for recording proxy data.
[PROXY REC(P2)]: Records proxy data to a P2 card.
[PROXY REC(P2&SD)]:
Records proxy data to both of a P2 card and SD memory card.
[STREAMING]: Outputs video stream.
[OFF]:
Does not record proxy data or output streaming.
f Factory setting: [OFF]
[PROXY REC MODE] Sets the recording mode of proxy data.
[LOW 2CH MOV], [HQ 2CH MOV], [SHQ 2CH MOV], [AVC-G6 2CH MOV]
f Factory setting: [HQ 2CH MOV]
[STREAMING MODE] Sets the transfer mode for streaming.
[LOW], [HQ], [AVC-G6], [SHQ (QoS)], [AVC-G (QoS)]
f Factory setting: [HQ]
[PROXY DISP] Selects whether to display proxy data recorded information or messages in the viewfinder.
[ON]: Displays proxy recording information and SD memory card remaining capacity at the start of
recording. Warning information is displayed at all times.
[OFF]: Displays proxy and SD memory card warning information for only three seconds when warning
occurs.
f Factory setting: [OFF]
[QoS MAX RATE] Sets the maximum bitrate for video data when the QoS is operating. This setting is used when the
streaming distribution is started from the operation of the camera.
This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING
SETTING] → [START TRIGGER].
[256Kbps], [512Kbps], [1Mbps], [1.5Mbps], [2.5Mbps], [3.5Mbps], [6Mbps], [9Mbps]
f Factory setting: [9Mbps]
[9Mbps] cannot be selected when [STREAMING MODE] is set to [SHQ (QoS)].
[QoS MIN RATE] Sets the minimum bitrate for video data when the QoS is operating. This setting is used when the
streaming distribution is started from the operation of the camera.
This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING
SETTING] → [START TRIGGER].
[256Kbps], [512Kbps], [1Mbps], [1.5Mbps], [2.5Mbps], [3.5Mbps], [6Mbps], [9Mbps]
f Factory setting: [256Kbps]
[STREAMING LATENCY] Sets the delay mode during the streaming distribution. This setting is used when the streaming distribution
is started from the operation of the camera.
This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING
SETTING] → [START TRIGGER].
[NORMAL]: Set this to prioritize the stability of streaming.
[SHORT]: Set this to prioritize the reduction of streaming delay.
f Factory setting: [NORMAL]
f For details on relations between dual codec recording and system mode, refer to “System modes and recording functions” (page 79).
f When streams are output, proxy data is not recorded.
f If [CODEC USAGE] cannot be changed, change the [PROXY REC MODE] or [STREAMING MODE] setting.
f When the main menu → [SYSTEM MODE] → [LINE&FREQ] is set to [480-59.94i] or [576-50i], proxy recording mode is fixed to [LOW 2CH MOV], and
[PROXY REC MODE] is not displayed.
f When the main menu → [SYSTEM MODE] → [LINE&FREQ] is set to [1080-59.94P], [1080-50P], [1080-23.98PsF], [480-59.94i], or [576-50i], the
streaming function is disabled and the following items are not displayed.
-
[STREAMING MODE]
-
[QoS MAX RATE]
-
[QoS MIN RATE]
-
[STREAMING LATENCY]
Checking the setting status
Push the <DISP/MODE CHK> switch on the camera towards the <CHK> side twice to check the setting values of [CODEC USAGE], [PROXY REC
MODE], and [STREAMING MODE] with the mode check function.
Recording modes and recording signals (video/audio)
The following settings are available only when the main recording is set to [1080-59.94i], [1080-50i], [720-59.94P], or [720-50P] from the main menu →
[SYSTEM MODE] → [LINE&FREQ]. For details, refer to “System modes and recording functions” (page 79).