Panasonic AJ-PX230 Series, Руководство по эксплуатации

Страница: 147 / 169

– 147 –
Chapter 7 Display — Screen status display
No Item Shooting Playback
<DISP/
MODE CHK>:
<CHK>
<DISP/MODE
CHK>: <OFF>
<DISP/MODE CHK>: <ON>
[OTHER DISPLAY]
[ALL] [PARTIAL] [USER]
36 One clip recording mode status display
l
—
l
—
l l l
37 Recording/playback operation status
display
l l l
—*
3 l l l
38 <AUTO/MANUAL> switch operation
display
l
—
l
—
l l l
39 GPS display
l
—
l
—
l
—
l
40 HD SDI REMOTE recording status
l *4
—
l
*
4
—
l
*
4 l
*
4 l
*
4
41 Audio monitor volume adjustment
display
l l
—*
1
—*
1
—*
1
—*
1
—*
1
42 Front audio level volume display
l
— —*
1
—*
1
—*
1
—*
1
—*
1
*1 May be displayed depending on other settings.
*2 Displayed when the remaining capacity becomes smaller.
*3 Displayed during shooting.
*4 Constantly displayed when set to [HD SDI REMOTE].
Mode check display
The camera settings and status can be displayed on the viewfinder or LCD monitor screen for check.
Each time the <DISP/MODE CHK> switch on the camera is pushed towards the <CHK> side, the five screens are switched.
[STATUS] screen display
→ [FUNCTION] screen display → [AUDIO] screen display → [USER SW] screen display → [META INFO] screen display → no
display
Each screen is displayed for approximately five seconds. Pushing the <DISP/MODE CHK> switch towards the <CHK> side while the screen is displayed
moves to the next screen.
[FUNCTION] screen
Displays the video output status and information of the recording media.
[SDI OUT] — Displays the status of the signal output from the <SDI OUT> terminal.
[TYPE]
Displays the format of the signal output from the <SDI OUT> terminal by [HD-SDI]/
[SD-SDI].
[CHAR]
Displays the superimposition status of characters selected in the main menu →
[OUTPUT SEL] → [SDI OUT CHAR] by [ON]/[OFF].
[P2CARD STATUS]
—
Displays the status, remaining recording capacity, and total capacity of the microP2
memory card inserted in the card slot.
The statuses of cards to be displayed are as follows:
[ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/
[FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD]
For details, refer to “microP2 memory card access LED and status of microP2 memory
card” (page 39).
[TOTAL] Displays the remaining capacity/total capacity of slots 1 and 2 altogether.
[SLOT1]
Displays the status of the microP2 memory card in slot 1 and remaining capacity/total
capacity.
[SLOT2]
Displays the status of the microP2 memory card in slot 2 and remaining capacity/total
capacity.
[AUDIO] screen
Displays audio settings and the selection status of each recording channel.
[AUDIO]
[INT MIC]
Displays the built-in microphone status set in the main menu → [AUDIO SETUP] →
[INPUT SETTING] → [INT MIC].
f
[STEREO]: Records audio from two directions in the front with the 2ch stereo
microphone.
f
[MONO]: This mode records clearer audio from the front by enhancing the
directionality forward like a shotgun microphone. Audio recorded on the left and right
are the same.
f
[OFF]: Disables audio of the built-in microphone.
[AUDIO OUT]
Displays the audio input signal status set in the main menu → [AUDIO SETUP] →
[OUTPUT SETTING] → [AUDIO OUT].
[CH1/CH2]/[CH1]/[CH2]/[CH3/CH4]/[CH3]/[CH4]
[A.IN]
[CH1/2/3/4]
Displays the input status of each channel.
[INT(L)]/[INT(R)]/[INPUT1]/[INPUT2]
[LEVEL]
[CH1/2/3/4]
Displays the recording level adjustment method currently selected on each channel.
f
[VR]: Displayed when manual adjustment using the adjustment dial is set.
f
[MENU]: Displayed when manual adjustment using [LEVEL CONTROL CH3]/[LEVEL
CONTROL CH4] is set in the main menu → [AUDIO SETUP] → [RECORDING CH
SETTING].
f
[AUTO]: Displayed when automatic adjustment is set.
[F.VR]
[CH1/2/3/4]
Displays by [ON]/[OFF] whether the <F.AUDIO LEVEL> dial is enabled on the channel to
which [VR] (manual adjustment by adjustment dial) is displayed in [LEVEL].