Panasonic AJ-P2C008HG Скачать руководство пользователя страница 58

Страница: 58 / 102

Using Play List: Playing Back Play Lists

U
s

g P

Li
st

Playing Back Play Lists

During play list playback, you can select whether the time

code should be replaced and output as a continuous value or

the time code of each clip should be output. You can set the

time code start value when it is replaced at output.

Open the play list screen.

Press the MENU button.

Use the cursor buttons to choose [SETTING] –

[REPLACE TC] – [REPLACE].

Select [ON] and press the SET button.

This replaces the playback time code.

◆

NOTE:

• When [OFF] is set, the time code is not replaced, instead the

time code of each clip is output.

• When [OFF] is set, go to step 7 and end setup.

Use the cursor buttons to choose [SETTING] –

[REPLACE TC] – [START TC] and press the SET

button to enter the start time code.

The initial value of the start time code is 00:00:00:00 when

replaced.

Use the cursor buttons to choose [SETTING] –

[REPLACE TC] – [DROP FRAME]. Then press the

SET button and select [DF] (drop frame) or [NDF]

(non drop frame).

◆

NOTE:

• A [DF] setting cannot be made at 24PN.

Press the MENU button to end setup.

Setting the Playback Time Code (TC)

Содержание AJ-P2C008HG







































































































Результаты поиска

Содержание AJ-P2C008HG

Отзывы:

Похожие инструкции для AJ-P2C008HG

Бренды по названию

Популярные бренды

Panasonic AJ-P2C008HG, Руководство пользователя

Результаты поиска

Содержание AJ-P2C008HG

Отзывы:

Похожие инструкции для AJ-P2C008HG

Бренды по названию

Популярные бренды