57
Adjustments and Settings for Recording : Setting Time Data
A
d
ju
stm
ents and S
e
tti
ngs f
o
r
Rec
o
rdi
n
g
*1
It will not be slaved to a TC or UB value that is input in the SDI IN connector.
*2
Can be slaved to values input through the DVCPRO/DV connector but not to the TC for TC IN connector.
*3
If the option menu FRAME RATE UB is set to MENU, then recording is performed as per the UB or VITC UB mode. If
this is the case, however, edit tools (e.g. PC edit software) cannot record the required information.
*4
For free run, the time code is slaved to the time code input through the TC IN connector.
*5
For free run, the time code is slaved to the time code input through the TC IN connector if it is a non-drop frame.
*6
When the option UB MODE is set to EXT, then the bits are slaved to the user bits input through the TC IN connector.
*7
If the option UB MODE is set to EXT, then the bits are slaved to the user bits input through the DVCPRO/DV
connector.
*8
Regardless of the menu settings, frame rate information is always recorded. During playback, the information is output
after being converted into pull-down frame rate information.
*9
When the UB MODE is set to [FRM.RATE], the pull-down frame rate information read out from the UB in the VAUX area
is output during playback.
*10 For details on this item, refer to [Recording formats and output connector signal formats] (page 43)
The user bits (UB) to be recorded in the sub-code area are
selected through the menu option UB MODE. The user
bits (VITC UB) to be recorded in the VIDEO AUX area are
selected through the menu option VITC UB MODE.
USER (UB MODE only)
The included user value is recorded. A user value is
input through the display window. For more information
about how to input a user value, see[Inputting a user
value
] (page 57). The recorded user value is retained
even if the power is turned off.
TIME
The time kept by the built-in clock is recorded.
DATE
The hour digits for date and time kept by the built-in
clock are recorded.
EXT (UB MODE only)
The user bits value input through the TC IN connector
is recorded. When the menu option REC SIGNAL is
set to 1394, then the value is slaved to the user bits
value from the DVCPRO/DV connector. The included
user’s value will also be this input value.
TCG
The time code value is recorded.
FRM.RATE
The frame rate information for camera shooting is
recorded. For more information, see [Frame rate infor-
mation recorded in user bits
REGEN
The user bits last recorded on the current target P2
card is read and recorded as is.
USER/EXT
（
VITC UB MODE only
）
The included user’s value is recorded as the user bits
for the VIDEO AUX area. It is the same value as the
user bits indicated when the option UB MODE is set to
“USER” or “EXT”.
1
Position the DISPLAY switch at [UB].
2
Position the TCG switch at [SET].
When the left digit starts blinking you can change the
value.
3
Use CURSOR buttons to set the user bits.
!
button:
Shifts the target (blinking) digit to the right.
"
button:
Shifts the target (blinking) digit to the left.
#
button:
Advances the blinking number by one digit.
$
button:
Winds back the blinking number by one digit.
4
Position the TCG at [F-RUN] or [R-RUN].
5
Go to the <TC/UB> screen from the MAIN
OPERATION page, and set the menu option UB
MODE to “USER”.
Notes
z
When the TCG switch is positioned at [SET],
thumbnails cannot be manipulated.
z
To confirm VICT UB, press the HOLD switch to
display VTCG on the display window.
Setting of the user bits
Inputting a user value
CURSOR and SET buttons
HOLD switch
Display
window
DISPLAY switch
TCG switch
AJ-HPX2000P(VQT1D27-1)E.book 57 ページ ２００７年７月３０日 月曜日 午後１時３１分
