– 84 –
Chapter 4 Adjustments and Settings for Recording — Handling setting data
Handling setting data
Setting data file configuration
F1 to F6 scene files can be saved internally on the camera matched to scene file numbers.
When an SD memory card is used, a maximum of four data of F1 to F6 can be batch-saved to files in the card for reading and use later on.
Also,one set of setting menu values (including SmartUI setting values) can be saved internally on the camera as a user file, and up to four sets can be
saved to an SD memory card.
The figure below shows the configuration of setting data files on the camera.
)GHIDXOW
>6&(1(),/(@
IDFWRU\GHIDXOWV
>6&(1(),/(@VFUHHQ
>6&(1(),/(@VFUHHQ
)GHIDXOW
)GHIDXOW
)GHIDXOW
)GHIDXOW
)GHIDXOW
)FXUUHQWYDOXH
>6&(1(),/(@
FXUUHQWRSHUDWLRQVWDWXVYDOXHV
)FXUUHQWYDOXH
)FXUUHQWYDOXH
)FXUUHQWYDOXH
)FXUUHQWYDOXH
)FXUUHQWYDOXH
)VDYHGYDOXH
>6&(1(),/(@
YDOXHVVDYHGRQWKHFDPHUD
)
)
)
)
)
)
>6&(1(
),/(@
)
)
)
)
)
)
>6&(1(
),/(@
)
)
)
)
)
)
>6&(1(
),/(@
)
)
)
)
)
)
>6&(1(
),/(@
>86(5),/(@
>86(5),/(@
>86(5),/(@
>86(5),/(@
>86(5),/(@GHIDXOW
>86(5),/(@
IDFWRU\GHIDXOWV
>27+(5)81&7,216@VFUHHQ
>86(5),/(@ĺ>,1,7,$/@
>27+(5)81&7,216@VFUHHQ
>86(5),/(@ĺ>/2$'@>6$9(@
>&$5')81&7,216@VFUHHQ
>6&(1(),/(@ĺ>/2$'@>6$9(@
>6&(1(),/(@QXPEHUXQLW
)WR)EDWFK
>86(5),/(@FXUUHQWYDOXH
>86(5),/(@
FXUUHQWRSHUDWLRQVWDWXVYDOXHV
>86(5),/(@VDYHG
YDOXH
>86(5),/(@
YDOXHVVDYHGRQWKHFDPHUD
>6&(1(),/(@
6'FDUG
>86(5),/(@
6'FDUG
)VDYHGYDOXH
)VDYHGYDOXH
)VDYHGYDOXH
)VDYHGYDOXH
)VDYHGYDOXH
>&$5')81&7,216@VFUHHQ
>6&(1(),/(@ĺ>/2$'@>6$9(@
6'FDUG
>,1,7,$/@
>/2$'@>6$9(@
$*+3;3$*+3;(-$*+3;(1
@
@
NOTE
t
When the [MENU INIT] item on the setting menu [OTHER FUNCTIONS] screen is executed, all current operation status values and values
saved on the camera of F1 to F6, and the current operation status values and values saved on the camera in user files can be batch-
returned to factory defaults. However, [TIME ZONE] settings cannot be returned to factory defaults.
t
Operations on setting data files may result in error during playback or when the [PC MODE] item on the setting menu [PC/USB/LAN] screen
is set to [ON]. Set the [PC MODE] item to [OFF] before performing operations.
t
When recording is possible by combining to the previous clip by one-clip recording (i.e. when [1
"
CLIP] is displayed), operations cannot be
performed on scene files or user files. Close the menu and press the <STOP> button for approximately two seconds to stop combining to the
clip, and try the operations again.
Setting up using SD memory cards
An SD or SDHC memory card (optional) can be used as a setup card that stores up to four files of setting menu content.
Use of this data allows you to quickly reproduce optimum setup states.
Handling SD memory cards
The SD memory card can be removed and inserted, either before or after the power is turned on.
Inserting SD memory cards
Open the slot cover, insert the card into the SD memory card slot with the label side of the SD memory card (optional) upward, and close the slot cover.
