Panasonic AFP0HC32ET Скачать руководство пользователя страница 70

Страница: 70 / 102

Startup and Operation

5-2

5.1 Startup Operation of Cyclic Communication

5.1.1 When FP0H is Originator

When the FP0H is originator, the FP0H operates in the following order after it is powered on.

Power ON

Resolves IP address.

Starts each communication

application task.

Starts EtherNet/IP task.

Connects to targets according to

Scan List.

Starts sending/receiving data from

targets whose connection are

established.

Refreshes the data received by

FP0H from targets.

Communications with all targets are

normally performed.

IP address fixed flag

(R9342) turns ON.

EtherNet/IP preparation

done flag (R9350) turns ON.

The corresponding bits of

cyclic communication

normal node tables turn ON.

EtherNet/IP all nodes normal

communication active relay

(R9351) turns ON.

Resolved.

Started.

Refreshed.

All nodes are

communicating.

KEY POINTS

•

For confirming if the connection with each target is established or not,

check "Cyclic communication normal node table". The cyclic

communication state node table can be read by F465 ETSTAT instruction.

The communication state of each connection can be checked.

•

For confirming that the connections with all targets have been established,

check the all nodes normal communication active relay (R9351).

Содержание AFP0HC32ET







































































































Результаты поиска

Содержание AFP0HC32ET

Отзывы:

Panasonic AFP0HC32ET, Руководство пользователя, Страница: 70 / 102

Результаты поиска

Содержание AFP0HC32ET

Отзывы: