Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 94

Страница: 94 / 160

Chapter 5. Clearing Data

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

5.3 Deleting Site Files

Use the

SITE

submenu to clear site files from the DF868’s memory. Use the

[SCREEN]

key to activate the desired

display pane, and refer to the menu map in Appendix A, page A-8 while completing the following steps:

To access the

Clear Menu

, press the

[CLR]

key.

If you have activated the security feature (see Chapter 1,

Programming Site Data,

page 50 for details), enter the

assigned password and press

[ENT]

Press

[F2]

SITE

At the

Site Name

prompt, use the [



, [



and

[F1]-[F4]

keys to select a site file for deletion. To leave the

SITE

submenu, press the

[EXIT]

key.

Note:

At the

SITE NAME

prompt, the option bar shows the names of all site files currently stored in memory.

Press

[F1] to abort the procedure

, or press

[F2] to Clear the specified site file. If any site files remain in memory,

the Site Name prompt repeats.

When all of the stored site files have been cleared or the

[EXIT]

key has been pressed at the

SITE NAME

prompt, the

programming sequence resumes at this point.

5.4 Deleting Log Files

Use the

LOG

submenu to clear log files from the Model DF868’s memory. Press the appropriate side of the

[SCREEN]

key to activate the desired pane of the data display screen, and complete the following steps:

To access the

Clear Menu

, press the

[CLR]

key.

If you have activated the security feature (see Chapter 1,

Programming Site Data,

page 50 for details), enter the

assigned password and press

[ENT]

Press

[F3]

LOG

At the

Name

prompt, the option bar shows the names of all log files currently stored in memory. Use the [



, [



and

[F1]-[F4]

keys to select a site file for deletion. To leave the

LOG

submenu, press the

[EXIT]

key.

Press

[F1]

to abort the procedure or press

[F2]

Clear

the specified log file. If any log files remain in memory, the

Name

prompt repeats.

When all of the stored log files have been cleared or the

[EXIT]

key has been pressed at the

NAME

prompt, the

programming sequence resumes at this point.

Procedure Options

Do one of the following:
•

Press

[F1]-[F3]

to enter one of the submenus.

•

Press the

[EXIT]

key to return to the data measurement display.

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 94 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: