Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 85

Страница: 85 / 160

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

Chapter 4. Printing Data

4.3 Print Live Data

Use the

DATA

submenu to print live measurement data as it is collected. The data may be printed in either numeric

or graphical format, with a user specified time increment.

IMPORTANT:

Make sure that a printer has been properly set up before proceeding with this section.

To print live measurement data, refer to Figure 16 on page 103

and complete the following steps:

To access the

Print Menu

, press the

[PRNT]

key.

Note:

The

Print Menu

is not protected by the security feature and a password is never required to access this

menu.

Press

[F1]

DATA

Press

[F1]

to print the data in numeric format or press

[F2]

to print the data in graphical format.

• If you press

[F1], go to step 4.

• If you press

[F2], go to step 8.

4.3.1

Numeric Format

Use the [



, [



and

[F1]-[F4]

keys to select the first parameter to be printed. See Table 38 for a list of the

available options.

Refer to Chapter 3,

Diagnostics

, of the

Service Manual

for a discussion of the many parameters accessible via the

DIAG

option.

Note:

The units assigned to the parameters in Table 38 are those selected in the

User Program

(

SYSTM

submenu).

Table 38: Measurement Parameter Options

Option Bar Choice

Description

[F1]

VEL

Flow Velocity

[F2]

VOLUM

Volumetric Flow

[F3]

+TOTL

Forward Totalized Volume Flow

[F4]

-TOTL

Reverse Totalized Volume Flow

[



+ [F1]

MDOT*

Mass Flow

[



+ [F2]

+MASS*

Forward Totalized Mass Flow

[



+ [F3]

-MASS*

Reverse Totalized Mass Flow

[



+ [F4]

POWER**

Energy Flow Power

[



+ [



+ [F1]

+ENRG**

Forward Energy Flow

[



+ [



+ [F2]

-ENRG**

Reverse Energy Flow

[



+ [



+ [F3]

DIAG

Diagnostic

* Available only if “Mass Flow (static)?” = YES

**Available only if “Energy Option” = YES

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 85 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: