Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 80

Страница: 80 / 160

Chapter 3. Logging Data

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

3.4 Creating an ERROR Log

Use the

ERROR

submenu to create a new error log and to select the logging parameters. An error log updates every 5

seconds (when the display updates), but only if a new error condition occurs. Error logs have a fixed length of 2 pages

and contain sixty records per page. Each record shows the time of the error, the measurement parameter values at

that time, and the error code message. The logged values of the chosen measurement parameters at the time of the

error condition provide valuable troubleshooting information.
Press the appropriate side of the

[SCREEN]

key to activate the desired pane of the display screen, and complete the

following steps:

To access the

Log Menu

, press

[LOG]

If you have activated the security feature (see Chapter 1,

Programming Site Data

, page 50 for details), enter the

assigned password and press

[ENT]

Press

[F4]

ERROR.

Use the [



, [



and

[F1]-[F4]

keys to inspect a completed log or to change an active log, or enter a new

Name

(up to 5 characters) and press

[ENT]

to create a new log file.

Note:

The option bar lists all error logs currently stored in memory. Recall that a flashing asterisk (*) appears at

the far right of the locator bar if the Model DF868 is currently logging data (see Chapter 3,

Operation

, page

3-4 of the

Startup Guide

At the

Log Message

prompt, enter a brief description (up to 21 characters) of the log and press

[ENT]

Use the [



, [



and

[F1]-[F4]

keys to select the first parameter to be logged. See Table 36 for a list of the

available options.

IMPORTANT:

Only the first parameter logged may be graphically displayed (see page 63).

Table 36: Measurement Parameter Options

Option Bar Choice

Description

[F1]

VEL

Flow Velocity

[F2]

VOLUM

Volumetric Flow

[F3]

+TOTL

Forward Totalized Volume Flow

[F4]

-TOTL

Reverse Totalized Volume Flow

[



+ [F1]

MDOT*

Mass Flow

[



+ [F2]

+MASS*

Forward Totalized Mass Flow

[



+ [F3]

-MASS*

Reverse Totalized Mass Flow

[



+ [F4]

POWER**

Energy Flow Power

[



+ [



+ [F1]

+ENRG**

Forward Energy Flow

[



+ [



+ [F2]

-ENRG**

Reverse Energy Flow

[



+ [



+ [F3]

DIAG

Diagnostic

* Available only if “Mass Flow (static)?” = YES

** Available only if “Energy Option?” = YES

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 80 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: