Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 122

Страница: 122 / 160

Appendix C. Programming with PanaView

114

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

C.4.1 Setting up Ethernet Communications

If you have selected TCP/IP in step 6 on the previous page, the Setup Communications window appears similar to

Figure 20.

Figure 20: Setup Communications for TCP/IP

Type in the desired

Name

and

Timeout

(in milliseconds).

2. In the

IP Address

text box, enter the IP address. If the IP address is unknown, run the Device Discovery software

utility. All units found will be identified by their MAC address and the assigned IP address. In the

Port Number

box,

enter 2101 (the default value).

3. Click [OK] to complete data entry.

IMPORTANT:

If you are using Ethernet communications, be sure the DF868 is set up with the default

communications parameters: 9600 baud, no parity, no handshaking, 8 data bits and 1 stop bit. The

port number must match the “Enable Raw TCP access using TCP Port” assignment shown under the

Device Discovery

“TCP Server Settings” menu (

Configuration>Serial Ports>Port

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 122 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: