Panametrics CGA 351 Скачать руководство пользователя страница 80

Страница: 80 / 119

Chapter 5.

CGA 351 User’s Manual

Remove the terminal board fuse (see Figure 6 on page 14) and check it for continuity. If the fuse is blown, replace

it with a new fuse of the same size and type listed in Chapter 6,

Specifications.

If the fuse was good, the main voltage supply is bad. Check the external disconnect device and/or the main

voltage source to that device.

Based on the recommended action in Table 136 above, proceed to the appropriate section for instructions. If the

problem has still not been resolved at this point, contact the factory for assistance.

5.1.3

Oxygen Measurement Errors

This section discusses each of the following possible oxygen errors:
•

oxygen concentration stuck at 20.93%

•

oxygen concentration reading above 100%

•

oxygen reading too low

• oxygen reading too high

Refer to the appropriate section of this chapter and to Figure 5 on page 87 for help in troubleshooting each of the

above situations.

Note:

For information regarding component locations and/or wiring connections in an optional enclosure, see

Appendix C.

5.1.3.1

Oxygen Concentration Reads Constant 20.93%

This condition is unusual and is likely to be caused either by a short in the oxygen sensor wiring, a severe air leak in

the plumbing or a defective digital display. A brief description of how to remedy this problem is presented below.

WARNING!

The sensor enclosure is hot. Use heat-resistant gloves when handling the enclosure.

IMPORTANT:

This symbol indicates Caution - dangerously hot surfaces:

Checking the Oxygen Sensor Wiring

Refer to Figure 5 on page 87 for the location of the oxygen sensor clips, and check for a short circuit in the contact clip

wiring (two wires touching). If this does not correct the problem, proceed to the next section.

Note:

For information regarding component locations and/or wiring connections in an optional enclosure, see

Appendix C.

Содержание CGA 351
























































































































Результаты поиска

Содержание CGA 351

Отзывы:

Panametrics CGA 351, Руководство пользователя, Страница: 80 / 119

Результаты поиска

Содержание CGA 351

Отзывы: