manualshive.com logo in svg

Pall PadMixer 1000 Premium, Инструкция по эксплуатации

Поделиться
Скачать
Pall PadMixer 1000 Premium Скачать руководство пользователя страница 39

020-17467-00 Instructions For Use PadMixer 1000 Premium RevD

 

 

39 
 

 

Figure 43: Printer with paper roll 

 

If required, press the FEED button to feed the paper in the printer or the PRINT button to print 
out a test  label. 

 

Figure 44: Print and Feed buttons of the printer 

 

6.5  Adjusting the inflation pressure 

The outgoing pressure (to the biocontainer) can be adjusted by means of the manometer 
underneath the mixing head cover plate (an L-shaped plate). This pressure is pre-set to a 
maximum of 500 mbar. 

If however a higher air flow rate is required, this pressure can be adjusted. There is no risk 
for creating an overpressure inside the bag since the bag detections will stop the inflation in 
time. 

Note however that a too high gas flow might cause issues if certain filters are present on the 
gas inlet tubing, or if the gas inlet tubing has a very small ID or shows locally diameter 
reductions. 

To change the pressure, the inflation must be switched on and the outlet tubing (towards the 
bag) must be kept closed. Only then the manometer will indicate the outgoing pressure on 
the display. 

 

Содержание PadMixer 1000 Premium

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды