PairGain 150-1140-42 Скачать руководство пользователя страница 45

Страница: 45 / 56

150-319-142-01

December 22, 1997

Revision 01

HLU-319 List 4B

PairGain Engineering - Plant Series

Table 5.

Addressable 3 and 4 (A3LB and A4LB) Repeater Loopback

Commands*

Position

Name

Code

HLU-319 LU FROM NI

NLOC

1111(F)**1111(F)0001(1)1110(E)

HLU-319 LU from CI

CREM

0011(3)1111(F)0001(1)1110(E)

HRU LU FROM NI

NREM

1111(F)1111(F)0000(0)0010(2)

HRU LU FROM CI

CLOC

0011(3)1111(F)0000(0)0010(2)

HRU LU FROM NI

SMJK

11000 11000 11000...

HRU LU FROM NI

SMJK

100000 100000 100000...

HRU LU FROM NI (ESF-DL)

SMJK

1111(F)1111(F)0100(4)1000(8)

HLU and HRU LD FROM NI
OR CI

Loopdown

11100 11100 11100...

HLU and HRU LD FROM NI
OR CI

Loopdown

100 100 100...

HLU and HRU LD FROM NI
OR CI (ESF-DL)

Loopdown

1111(F)1111(F)0010(2)0100(4)

* The left-most bit arrives first in all sequences. The detection algorithm functions

reliably with a random 10

-3

Bit Error Ratio (BER) on the facility. Note that the

entire arming and loopback sequence can be initiated at the remote HRU
location.

** The number in ( ) identifies the HEX number for the 4-bit group.

Содержание 150-1140-42

























































Результаты поиска

Содержание 150-1140-42

Отзывы:

Бренды по названию

Популярные бренды

PairGain 150-1140-42, Руководство пользователя

Результаты поиска

Содержание 150-1140-42

Отзывы:

Бренды по названию

Популярные бренды