Pacific Sun Kore 7th Скачать руководство пользователя

Страница: 70 / 79

Page 70

Kore 7th Manual / kHLab Edition

Option 1:

Verify the USB Serial Port COM

number

under “

Device Manager

”.

17. Kore 7th Software and Firmware Upgrade

3. Windows Operating System has the two following options to verify the correct USB Serial

Port COM

number

1. “

Device Manager

”

2. “

Devices and Printers

”

Connect your Laptop/PC to the Kore 7th

dosing station via USB port.

Windows Operating System should be

able to discover and install the new Kore 7th

USB device and show the communication

COM port number.

NOTE

If for the first time, Windows will not be able

to install the new Kore 7th device (especially

under Window 7) then download from

the Internet and install the USB-to-Serial

Converter Drivers:

https://www.ftdichip.com/Drivers/VCP.htm

(CDM v2.12.28 WHQL Certified)

Warning!

Switching off the power supply during the Firmware updating process

may damage your doser CPU. Uploading wrong Firmware may damage

your doser and void your warranty. The damage may require returning the

doser to our service department to restore it’s original functionality.

Use only

dedicated firmware upgrade software

available for

download on www.Pacific-Sun.eu in

Download

section.

Содержание Kore 7th
















































































Результаты поиска

Содержание Kore 7th

Отзывы:

Похожие инструкции для Kore 7th

Бренды по названию

Популярные бренды

Pacific Sun Kore 7th, Руководство пользователя

Результаты поиска

Содержание Kore 7th

Отзывы:

Похожие инструкции для Kore 7th

Бренды по названию

Популярные бренды