Pacific energy FP30AR страница 44 Скачать руководство пользователя

Страница: 44 / 48

Installing The Front

To install the front;

1. Align and place the air control lever through the opening in the lower section of the Front Assembly

(Figure 3).

2. Tilt the front up and under the Brow. Lift up and guide the side tabs into the corresponding openings

located in the side brackets. Push the Front Assembly into the slots, until it drops slightly - engaging the
mounting tab locks.

3. To lock the Front Assembly in place, install the four black #8 Torx screws provided into the holes located

behind the Front Assembly.

• In the door opening behind the Front, there are four screw holes. These may require the door to be

removed ( open door and lift up on hinge side) to see and access them clearly.

Figure 51: FP30 Craftsman front Air Control clearance.

Figure 52: Openings for the front tabs and the position of the screws.

100000811_200418-48

FP30 Series B

Содержание FP30AR

















































Результаты поиска

Содержание FP30AR

Отзывы:

Похожие инструкции для FP30AR

Бренды по названию

Популярные бренды

Pacific energy FP30AR, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FP30AR

Отзывы:

Похожие инструкции для FP30AR

Бренды по названию

Популярные бренды