PACH & COMPANY AeGIS 7000 Series, Инструкция по установке и программированию, Страница: 23 / 33

73
SELECT TONE OR
PULSE DIALING
(Default setting is
tone)
If set to Tone: pulse phone
can’t unlock the door by
pressing 9.
If set to pulse: both tone
and pulse phone can
unlock the door by
pressing 9.
74
ENABLE OR
DISABLE AUTO
ANSWER
(Default setting is
Enable)
If Enable, the system will
answer an incoming call.
If disable, the system will
not answer an incoming
call.
This feature is useful if:
• Remote touch-tone
programming is used or
• For the tenant to call
the system in case the
tenant is not available at
the time the visitor call.
75
TURN ON OR OFF
KEY PRESS BEEP
(Default setting is
ON)
If ON, the system beep if
key is pressed.
If OFF, the system does
not beep if the key is
pressed.
If the system is set for
Multi (see Function Code
07),
same Function Code or different Function Code
to continue programming or press
*
to exit the
programming mode and you will hear “Three
Short Beeps” .
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 73 then press #, the
display shows:
Step 3 Enter 1 for Tone or 0 for Pulse then press #.
Step4 Press
*
then proceed to step 2 and select the
same Function Code or different Function Code
to continue programming or press
*
to exit the
programming mode and you will hear “Three
Short Beeps” .
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 74 then press #, the
display shows:
Step 3 Enter 1 to Enable or 0 to Disable , then press #.
Step4 Press
*
then proceed to step 2 and select the
same Function Code or different Function Code
to continue programming or press
*
to exit the
programming mode and you will hear “Three
Short Beeps” .
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 75 then press #, the
display shows:
Step 3 Enter 1 to turn ON key press beep or 0
turn OFF key press beep , then press #.
program another parameter or
tenant's directory, otherwise enter
91 then press # to disconnect the
call, you hear
“Three Short
Beeps” .
Step 1 Log on to programming mode,
see section 3.2 If you have
logged on proceed to step 2.
Step 2 Enter Function Code 73 then
press #, you hear
“One Short
Beep”.
Step 3 Enter 1 for Tone or 0 for Pulse
then press #, then press # and
you will hear
“ Two Short
Beeps”.
Step 4 Select another Function Code
to program another parameter or
tenant's directory, otherwise enter
91 then press # to disconnect the
call, you hear
“Three Short
Beeps” .
NOT AVAILABLE.
Step 1 Log on to programming mode,
see section 3.2 If you have
logged on proceed to step 2.
Step 2 Enter Function Code 75 then
press #, you hear
“One Short
Beep”.
Step 3 Enter 1 to turn ON key press
beep or 0 to turn OFF key press
beep then press #, then
press #and you will hear “Two
Short Beeps”.
FUNCTION CODE LOCAL PROGRAMMING TOUCH TONE PROGRAMMING
Pach and Company Chapter 3 Page 16
AeGIS 7000 Series PROGRAMMING
Select Func: _ _
TONE=1 PULSE=0: 1
Select Func: _ _
Auto Answer=1 : 1
Select Func: _ _
BEEP On=1 OFF=0: 1