background image

©2022 PACE Inc., Vass, North Carolina, All Rights Reserved                                                           Page 2 
 

 

 

Capabilities 

 

All capabilities are dependent on use of the appropriate accessories. Available handpieces and their functions are 
listed below. A manual is available for each handpiece with descriptions of the applications and recommended 
procedures for that tool. 
 
The MBT360 allows a total of two AccuDrive handpieces and one SensaTemp to be plugged into the continuously 
active Power Ports on its front. The dual-purpose vacuum/pressure pump system with PACE’s patented SNAP-
VAC Technology, provides the most vacuum available for desoldering applications. When used with an air pencil, 
the pressure control valve allows for precise adjustment for working with the smallest components. 
 

MBT360 Compatible Handpieces 

 

AccuDrive 

 

TD-200 handpiece – 

The most responsive soldering iron available. Uses tip-heater cartridges. TD-200 Kit P/N 

6993-0316-P1 Handpiece only P/N 6010-0166-P1 
 

MT-200 handpiece – 

Tip heater cartridge tweezers for SMD removal. MT-200 Kit P/N 6993-0323-P1 

Handpiece only P/N 6010-0169-P1 
 

SensaTemp 

 

PS-90 Soldering Iron– 

Provides a wide range of SMD and thru-hole installation and removal capability as well 

as unsurpassed thermal performance on heavy, multilayer thru-hole assemblies at safe, lower working 
temperatures. A wide variety of 3/16" shank, quick change thru-hole and SMD tips (for chip components, SOTs, 
SOICs and other components) are available. PS-90 Kit P/N 6993-0199-P1 Handpiece only P/N 6010-0131-P1 
 

SX-100 Sodr-X-Tractor handpiece –

 Air handpiece ideal for thru-hole desoldering on high-mass multilayer 

boards. SX-100 Kit P/N 6993-0213-P1 Handpiece only P/N 6010-0106-P1 
 

TT-65 ThermoTweez handpiece 

 Performs removal of PLCC (J Leaded), LCCC (leadless) and other 

surface mount devices. TT-65 Kit P/N 6993-0207-P1 Handpiece only P/N 7025-0001-P1 
 

TJ-70 Thermo Jet handpiece –

 Finger switch activated precision air pencil for the installation or removal of 

SMDs. TJ-70 Kit P/N 6993-0206-P1 Handpiece only P/N 7023-0002-P1 

 

Handpiece Tips 
 

A complete list of tips is available from your local PACE distributor or online at 

www.paceworldwide.com

.

 

 

 

 
 

Содержание MBT360




















Отзывы: