Section 1 - TireView
™
TPMS Instruction Manual
1.
Push and hold the
SET
button until it beeps. The
HI PRESSURE SET
parameter will blink at the bottom of
the screen. Push the
+
button and scroll through the parameters until
SET ID
appears.
2.
Quickly push and release the
SET
button. The first tire on the display will blink. If programing a different
tire, press the
+
button to move to the correct tire.
3.
Push the
SET
button again and the first digit of
FFF FFF
will flash. Push the
+
or
-
button to select the
correct number or letter. Push the
GO
button to move to the next digit. Repeat for all six digits.
4.
Push
SET
once to save the new codes. The display will beep, and the code will stop flashing. Push the
+
button to move to the next tire position, if necessary.
5.
To stop the sensor coding for any tire position, press
BACK
once.
FFF FFF
will reappear. No settings will
be saved.
6.
When all the sensors have been coded, pressing the
BACK
button twice will take you to the main screen.
Swap Tire Sensor Positions
Note:
This procedure is used if tires are being rotated or if programmed in wrong position.
1.
Press the
SET
button until the TPMS display beeps and then release it.
2.
Press and release the
+
button seven times until the tire swap icon,
, shows on the TPMS display.
3.
Press the
SET
button to enter the tire swap mode.
4.
Press the
+
button or the
-
button to select the tire sensor ID code (moved from position).
5.
Press the
SET
button.
6.
Press the
+
button or the
-
button to select the tire sensor ID code (moved to position).
7.
Press the
SET
button to swap the tire sensor ID code positions.
8.
Press the
BACK
button two times to return to the main screen.
Delete Sensor ID Codes from the TireView
™
TPMS Display
Delete a Sensor ID Code
1.
Press and hold the
SET
button until it beeps.
2.
Make sure
HI PRESSURE SET
is blinking at the bottom of the TPMS display.
3.
Press the
+
button and scroll/cycle until
LEARN ID
shows on the TPMS display.
4.
Press and release the
SET
button. The first tire on the TPMS display will blink.
5.
Press the
+
button or the
-
button to scroll/cycle to the desired tire sensor ID code.
6.
Press the
SET
button. The tire sensor ID code will flash on the TPMS display.
7.
Press and hold the
BACK
button.
8.
Listen for the TPMS display to beep THREE times, then release the
BACK
button. The code will change to
a flashing
FFF FFF
.
9.
Press the
SET
button one time. The TPMS display will beep and the tire sensor ID code will be deleted.
10.
Press the
BACK
button two times to return to the main screen.
Delete All Sensor ID Codes
1.
Press and hold the
SET
button until it beeps.
2.
Make sure
HI PRESSURE SET
is blinking at the bottom of the TPMS display.
3.
Press the
+
button and scroll/cycle until
LEARN ID
shows on the TPMS display.
4.
Press and release the
SET
button. The first tire on the TPMS display will blink.
5.
Press the
+
button or the
-
button to scroll/cycle to any programmed tire sensor ID code.
6.
Press the
SET
button. The tire sensor ID code will flash on the TPMS display.
© Pressure Systems International Inc.
All rights reserved worldwide.
19
T004-01 Rev 06-19
Содержание TireView
Страница 2: ......
Страница 5: ...Table of Contents Pressure Systems International Inc All rights reserved worldwide 5 T004 01 Rev 06 19...
Страница 6: ...Pressure Systems International Inc All rights reserved worldwide 6 T004 01 Rev 06 19...
Страница 8: ...Pressure Systems International Inc All rights reserved worldwide 8 T004 01 Rev 06 19...