P.I.T. E-PSR18-D4-A1, Руководство по эксплуатации

Страница: 7 / 10

Cordless Impact Drill
6
battery from the power tool. There is dan-
ger of injury when unintentionally actuating
the On/Off switch.
Open the keyless chuck by turning in rotation
direction
Ԯ
, until the tool can be inserted.
Insert the tool.
Firmly tighten the collar of the keyless chuck
2 by hand in rotation direction
ԯ
. This auto-
matically locks the drill chuck.
Dust/Chip Extraction
► Dust from materials such as lead-con-
taining coatings, some wood types,
minerals and metal can be harmful to
one’s health and cause allergic reac-
tions, lead to respiratory infections and/
or cancer.
Materials containing asbestos
may only be worked by specialists.
– Provide for good ventilation of the working
place.
– It is recommended to wear a P2 fi lter-class
respirator. Observe the relevant regula-
tions in your country for the materials to be
worked.
► Prevent dust accumulation at the work-
place.
Dust can easily ignite.
Operation
Starting Operation
Inserting the battery
Note:
Use of batteries not suitable for the
machine can lead to malfunctions of or cause
damage to the power tool.
Set the rotational direction switch to the center
position in order to avoid unintentional start-
ing. Insert the charged battery into the handle
so that it can be felt to engage and faces fl ush
against the handle.
Reversing the rotational direction (see fi g-
ure B)
The rotational direction switch is used to re-
verse the rotational direction of the machine.
However, this is not possible with the On/Off
switch actuated.
Rotate clockwise: Move the rotational direc-
tion switch on both sides up to the stop into
position
.
Rotate anticlockwise : Move the rotational
direction switch on both sides up to the stop
into position
.
Setting the operating mode
Drilling
Set the operating mode selector switch
to the “drilling” symbol.
Screwdriving
Set the torque selector setting ring to
the “screwdriving” symbol.
Impact drilling
Set the operating mode selector switch
to the “impact drilling” symbol.
Switching On and Off
To start the machine, press the On/Off switch
and keep it pressed.
The LED lights up when the On/Off switch is
halfway or fully pressed, and enables illumi-
nation of the screwing location in unfavorable
light conditions.
Adjusting the Speed
The speed of the switched-on power tool can
be variably adjusted, depending on how far
the On/Off switch is pressed.
Light pressure on the On/Off switch results in
a low rotational speed. Further pressure on
the switch results in an increase in speed.
Setting the torque
With the torque preselection ring , the re-
quired torque can be preselected in 17 steps.
The inserted tool is stopped as soon as the
set torque is reached.
Gear selection, mechanical
► The gear selector can be actuated at
standstill or when the machine is run-
ning. However, this should not be done
while operating at full load or maximum
speed.
1st gear:
Low speed range; for working with
large drilling diameters.
2nd gear:
High speed range; for drilling with
small drilling diameter.
Temperature Dependent Overload Protec-
tion
When using as intended for, the power tool
cannot be subject to overload. When the load
is too high or the allowable battery tempera-
ture range is exceeded, the speed is reduced.
The power tool will not run at full speed until
reaching the allowable battery temperature.
Protection Against Deep Discharging
The lithium-ion battery is protected against
deep discharging. When the battery is empty,
the machine is switched off by means of a
protective circuit: The inserted tool no longer
rotates.
Rapid Shut-off
The rapid shut-off feature enables better con-
trol of the power tool. The power tool shuts off
in case of sudden and unexpected rotation of
the power tool around the drilling axis.
The rapid shut-off feature is indicated by a