background image

 

from the area and keep people away until all the residual ozone has disassociated or 
dispersed.

  

 
Ozone has been shown to induce asthma attacks.  

Asthma suffers should not enter a newly 

ozonised airspace until all the residual ozone has fully dispersed and well ventilated with 
fresh air.

   

 
Ozone has a distinctive sharp odour and is normally detectable by smell at concentrations well 
below the OSHA 15-minute exposure limit.  Most people can detect the smell of ozone at 
concentrations around 1/10

th

 of the 15-minute exposure limit. 

 

A strong smell of ozone normally 

indicates an ozone concentration that exceeds the 15-minute exposure limit.

  Those people that 

lack a sense of smell should not operate this equipment.  Don’t attempt to confirm ozone 
production by directly smelling the ozone outlet.

   

 
 
 
 
 

CAUTIONS: 

 
1.

 

The unit is not waterproof, for indoor uses only.  DO NOT  allow water to enter.  Water 
damage is not covered by warranty. 

2.

 

DO NOT open, temper or try to repair the unit. The unit utilizes very high voltages that can 
result in injury. Do not touch an opened or tempered unit, while it is working. 

3.

 

DO NOT operate the unit in humid conditions (Humidity > 95%). 

4.

 

The suggested minimum room space is 30 m3 to avoid very strong smell of ozone when 
purifying water. 

5.

 

Keep the unit at a place where the unit is not reachable by children  

6.

 

Unplug when you no longer need it. 

7.

 

Inhalation of high-concentration or unmixed ozone gases can cause serious harmful 
physiological effects. Do not directly inhale ozone gas produced by this device. 

8.

 

DO NOT use unit within an environment with flammable gases or explosive materials. 

9.

 

DO NOT touch the machine with wet or damp hands. 

10.

 

Ensure that the cooling system is working properly for extended long period of usage. It is 
not recommended for prolonged use. 

11.

 

Avoid using the unit repeatedly in the warehouse of metals and lactoprene materials. 

12.

 

Use only ozone compatible  hoses  between the ozone generator and the injection point. 
Failure to use the correct materials could result in an undesirable leakage of ozone into the 
surrounding airspace.   

13.

 

DO NOT lubricate fittings or hoses with mineral oil or grease. 

  

Содержание HG-1500











Отзывы: