background image

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR 

YOUR BATTERY CHARGER.

1. 

Before using the charger read all instructions and cautionary markings on the charger, battery 

pack and the product using the battery pack.

2. 

This charger is not intended for any uses other than charging rechargeable batteries. Any other 

use may result in risk of fire, electric shock or electrocution.

3. 

Do not place any object on top of the charger or place the charger on a soft surface that may 

result in excessive internal heat. Place the charger in a position away from any heat source.

4. 

To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when 

disconnecting the charger.

5. 

Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise 

subjected to damage or stress.

6. 

An extension cord should not be used unless absolutely necessary. Use of an improper extension cord 

could result in the risk of fire, electric shock or electrocution.

7. 

Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in 

any way. Have it checked by an electrician or power tool repairer.

8. 

Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair 

is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.

9. 

To reduce risk of electric shock, unplug the charger from the outlet before attempting any clean-

ing. Removing the battery pack will not reduce this risk.

10. 

Never attempt to connect 2 chargers together.

11. 

DO NOT store or use the tool and battery pack in locations where the temperature may reach or exceed 

40ºC (such as inside sheds or metal buildings in summer).

12. 

The charger is designed to operate on standard household electrical power (240 volts). Do not 

attempt to use it on any other voltage!

13. 

The battery pack is not fully charged out of the carton. First read the safety instructions and then 

follow the charging notes and procedures.

14. 

The longest life and best performance can be obtained if the battery pack is charged when the 

air temperature is between 18 - 24ºC. Do not charge the battery pack in an air temperature below 

10ºC or above 40ºC. This is important and will prevent damage to the battery pack.

15. 

Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The 

battery can explode in a fire.

16. 

Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks 

or cracks, immediately discontinue use and do not recharge.

17. 

During charging, the battery must be placed in a well ventilated area.

CHARGER SAFETY WARNINGS

 ELECTRICAL SAFETY

 

WARNING!

 

When using mains-powered tools, basic safety 

precautions, including the following, should always be followed to 

reduce risk of fire, electric shock, personal injury and material damage.

 

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, 

before operating the tool. 

Save these instructions and other documents supplied with this tool for future reference.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for the UK.

This tools charger is double insulated; therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly 

qualified persons in order to avoid hazard.

Note:

 Double insulation does not take the place of normal safety precautions when operating this tool. 

The insulation system is for added protection against injury resulting from a possible electrical insulation 

failure within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect 

the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or 

defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead 

not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire 

and electric shock.
To reduce the risk of electric shock, we recommend the use of a residual current device (rated 30mA or 

less).
This appliance is not intended for use by persons (including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or 

instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

Read instruction manual

Double insulated

Indoor use only

Amps

A

Amp Hour

Ah

Volts

V

Hertz

Hz

DESCRIPTION OF SYMBOLS

Thermal cut out protection

2

SPECIFICATIONS

Input: 

 

200-250V AC 50/60Hz

Output: 

 

21V DC, 3A

Battery Charge Time: 

30Min - PXBP-150U (18V 1.5Ah)

 

 

40Min - PXBP-200U (18V 2.0Ah)

 

 

60Min - PXBP-300U (18V 3.0Ah)

 

 

80Min - PXBP-400U (18V 4.0Ah)

 

 

105Min - PXBP-520U (18V 5.2Ah)

1.   Charging Unit
2.  Charging Unit LED

ozito-diy.co.uk

1

FAST CHARGER

ORIGINAL INSTRUCTIONS

PXCG-030U

ONLINE MANUAL

Scan this QR Code with your 

mobile device to take you to the 

online manual.

Отзывы: