Adjusting The Output Pressure
The output pressure of the regulated pressure outlet can be adjusted
to suit the air tool connected and the task at hand.
1. To do so, first decrease the
pressure to 0psi by turning
the pressure regulator anti-
clockwise.
2. Then turn the pressure
regulator clockwise until the
desired pressure is shown on
the regulated pressure gauge.
WARNING!
DO NOT ATTEMPT TO ADJUST/MODIFY
THE SAFETY VALVE IN ANY WAY. THE SAFETY
VALVE INSTALLED ON THIS AIR COMPRESSOR
IS DESIGNED TO AUTOMATICALLY RELEASE
PRESSURE IN CASE OF EXCESS PRESSURE BUILD
UP IN THE TANK.
3. USAGE
Starting Up The Compressor
For best practice, the compressor should be run without any load
for 20 minutes before first use to lubricate the bearings and piston.
This procedure should also be performed if the compressor has been
stored for 6 months or more without operation.
1. Disconnect all air hoses from
the outlets and open the drain
valve fully with a spanner
to prevent pressurised air
buildup in the tank.
2. Make sure the power switch
is in the off position. Plug
the power supply cord into a
mains outlet and turn the unit
on.
3. Allow the compressor to run for 20 minutes without any loads/tools
attached and any liquid to drain from the tank.
4. Turn off the compressor and
close the drain valve. The
compressor is now ready for
use.
5. Attach the desired tool to one end of an air hose and the air hose to
an outlet depending on the tool or application.
6. Turn the compressor back on and adjust the regulated pressure to
the desired level once the pump has shut off and the compressor
has reached cut-off pressure
(8bar).
0
25
50
75
100
125
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
4
6
8
10
Lb/in²
(PSI)
kPA
(BAR)
PRESSURE GAUGE
kg/cm²
0
25
50
75
100
125
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
4
6
8
10
Lb/in²
(PSI)
kPA
(BAR)
PRESSURE GAUGE
kg/cm²
0
25
50
75
100
12
5
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
4
6
8
10
Lb/in²
(PSI)
kPA
(BAR)
PRESSURE GAUGE
kg/cm²
0
25
50
75
100
12
5
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
4
6
8
10
Lb/in²
(PSI)
kPA
(BAR)
PRESSURE GAUGE
kg/cm²
0
25
50
75
100
125
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
4
6
8
10
Lb/in²
(PSI)
kPA
(BAR)
PRESSURE GAUGE
kg/cm²
0
25
50
75
10
0
125
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
4
6
8
10
Lb/in²
(PSI)
kPA
(BAR)
PRESSURE GAUGE
kg/cm²
0
25
50
75
100
125
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
4
6
8
10
Lb/in²
(PSI)
kPA
(BAR)
PRESSURE GAUGE
kg/cm²
0
25
50
75
100
125
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
4
6
8
10
Lb/in²
(PSI)
kPA
(BAR)
PRESSURE GAUGE
kg/cm²
0
25
50
75
100
125
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
4
6
8
10
Lb/in²
(PSI)
kPA
(BAR)
PRESSURE GAUGE
kg/cm²
0
25
50
75
100
125
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
4
6
8
10
Lb/in²
(PSI)
kPA
(BAR)
PRESSURE GAUGE
kg/cm²
WARNING!
BEFORE CONNECTING THE
COMPRESSOR TO THE POWER SOURCE, CHECK
FOR BROKEN COMPONENTS AND ACCESSORIES.
ALSO CHECK FOR DAMAGE TO THE HOSE. DO NOT
PROCEED IF ANY COMPONENT OR PART SHOWS
SIGN OF WEAR OR DAMAGE. REPLACE THE PART
OR TAKE IT TO AN AUTHORISED REPAIRER.
