oxycom 3800OXYSTD Скачать руководство пользователя страница 61

Страница: 61 / 68

Operation procedures

Version 1.3, 2021-12-14

Status value

Reading

Unit

Brief description

W27:A-ExhaustAir

Status

Output value for building exhaust output (optional damper, fan or

Natural Ventilator box) (0% to 100% = 0 V to 10 V).

W28:A-OutdoorAir

Status

Output value for outdoor air/ventilation output (optional damper)

(0% to 100% = 0 V to 10 V)

(0% = closed / recirculation to 100% = 100% fresh air).

W29:A-AirOptimiz

Status

Output value for AirOptimizer (optional) exhaust output (damper or

fan) (0% to 100% = 0 V to 10 V)

( 0% = heating 'vertical' to 100% = cooling 'horizontal').

W30:A-Heating

Status

Output value for required heating capacity (external heat source)

(0% to 100% = 0 V to 10 V).

W31:Error codes

Status

Active errors (01 = only error code 01 and 01,03,06 = error codes 1, 3

and 6).

W32:Time

hh:mm:ss

Local time derived from thermostat.

W33:Software version

Shows the current software version on the Oxylogic.

5.2.4

Operating modes

Operating modes

Operating mode

Description

Heat reclaim

Unit is in heating mode (only when Heat Reclaim is activated).

Free cooling

Unit is in free cooling mode (cooling with outdoor air without water).

Standby

Stand-by.

Tank fill

Unit is filling the water tank.

Pre-wet

Unit is soaking the evaporative media (fans at low speed).

Cooling

Unit is in cooling mode.

OverflowProt

Drain valve open (short) to prevent tank overflow.

Drain

Unit drains the tank.

Rinse

Unit rinses/flushes the tank.

Hygiene dry-out

Unit is in hygiene dry-out mode.

System locked

Unit is locked. Error type A active.

5.2.5

Settings menu

To change a setting follow the procedure below::
1. Activate the settings menu: Press navigation button [1] and [2]

simultaneously for two seconds.

2. Scroll to setting to be changed: Press navigation button [2].
3. Edit setting: Press navigation button [1].

Содержание 3800OXYSTD





































































Результаты поиска

Содержание 3800OXYSTD

Отзывы:

Бренды по названию

Популярные бренды

oxycom 3800OXYSTD, Руководство пользователя

Результаты поиска

Содержание 3800OXYSTD

Отзывы:

Бренды по названию

Популярные бренды