oxycom 3800OXYSTD Скачать руководство пользователя страница 39

Страница: 39 / 68

Prepare the location

Version 1.3, 2021-12-14

Power supply to the external fuse.

4x0.75 mm

(shielded) cabling to and between OxyConnect the thermostats

and the IntrCooll®s.

Note
The gateway control box must be placed indoors.

3.16.3

Control by a Building Management System

IntrCooll® can be connected to a Modbus RTU (RS485) Building Management
System (BMS) as slave device.

The contractor must take care of the control system that regulates the
temperature control, fan speed and operation mode.

The Modbus interface information is available in a separate document. This can
be requested at Oxycom.

3.16.4

Control by an air handling unit

For pre-cooling purposes, the IntrCooll® can be controlled by and synchronized
with an air handling unit (AHU). There are two different control options:
-

Modbus RTU (RS485)

Analog control (6 wire cable)

3.16.4.1

Modbus RTU (RS485)

Controller I/0

I/0 type

I/0 function

Protocol

Connection type

Connection

J17

Isolated RS485 port

Modbus control

Modbus RTU

2-wire

Pin 1) A-

Pin 3) B+

3.16.4.2

Analog control (6-wire cable)

Controller I/0

I/0 type

I/0 function

Signal type

Connection type

Connection

Analog input

Fan speed input 0-10V

0 V = 0% fan speed

2-wire

Pin 1) 0 V

10 V = 100% fan speed

Pin 3) 0 V - 10

V input

J12

Digital input

Cooling On/Off

Off (no circuit) = Free Cooling

2-wire

Pin 1) +24

VDC output

On (circuit) = Cooling

Pin 3) Input

J23

Potential free contact

Alarm contact N.O.

Open (no circuit) = No alarm

2-wire

Pin 1) N.O.

Closed (circuit) = Active alarm

Pin 2) P

For the analog control method IntrCooll® PCB must switched to AHU Pre-cooling
mode. The following will apply:
-

J6: When the speed input signal of the external fan is less than 0.2V the unit
will go to stand-by.

Содержание 3800OXYSTD





































































Результаты поиска

Содержание 3800OXYSTD

Отзывы:

Бренды по названию

Популярные бренды

oxycom 3800OXYSTD, Руководство пользователя

Результаты поиска

Содержание 3800OXYSTD

Отзывы:

Бренды по названию

Популярные бренды