manualshive.com logo in svg

oxycom 3800OXYSTD, Руководство пользователя

Поделиться
Скачать
oxycom 3800OXYSTD Скачать руководство пользователя страница 37

Prepare the location

Version 1.3, 2021-12-14

37

1

2

3

4

5

To fully isolate the IntrCooll® from the mains, Oxycom recommends the
installation of an external maintenance switch / padlock switch between the
unit's main connection and the mains AC supply. Make sure the installation is
executed according to local regulations.

Padlock switch (example)

a

b

1 Switch ON (unlocked)

2 Switch OFF (locked / unlocked)

An external automated circuit breaker is not included in the package and must be
provided and installed by the contractor.

3.15.4

Mains power outlet

Oxycom recommends to install a mains power outlet near the IntrCooll®. This can
be used by the service technician for maintenance equipment.

3.16

Communication requirements

There are several possibilities to control the IntrCooll®. The correct choice
depends on the situation and specific requirements.

3.16.1

Thermostat control

IntrCooll® can be controlled by a thermostat, unless it is controlled by a BMS
system. The thermostat must be ordered separately.

If more than one IntrCooll®s are available at the location, each IntrCooll® must be
connected to a separate thermostat, unless they are controlled with OxyConnect
gateway (optional) or a BMS system.

Note
See the documentation of the thermostat for information on the connection
cable to the IntrCooll® or OxyConnect.
Note
The cable is not included and must be provided by contractor.

Содержание 3800OXYSTD





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды