Oxford Instruments ANDOR iKon-M Скачать руководство пользователя страница 30

Страница: 30 / 37

Version 1.4 rev 24 Apr 2019

IKon-M

APPENDIX A: TECHNICAL SPECIFICATIONS

(Note information given for iKon-M 934, refer to specifications for model variations)

General Specifications

Weight

4.2 kg [9 lb 4 oz], Power Supply = 0.65 kg [1 lb 4 oz]

Dimensions mm [inches]

W x H x D

110.7 x 231.0 x 137.2 mm [4.36 x 9.09 x 5.40 inches]

Environmental Specifications

Usage

Indoor use only

Operating Temperature

0°C to 30 °C ambient

Storage Temperature

-25°C to 50 °C

Operating Relative Humidity

<70% (non-condensing)

Ingress Protection

IP20

Overvoltage Category

CAT II. An overvoltage category of CAT II means that the equipment is designed to cope

with transient voltages above the rated supply that would be experienced by any product

connected to a mains socket in a building.

Rated Pollution

Pollution Degree 2. Normally only non-conductive pollution occurs. Occasionally, however, a

temporary conductivity caused by condensation must be expected.

Cooling vent clearance

100 mm minimum

Power Requirements

Mains Input

100-240 V AC 50/60 Hz

Cable pin-outs

(see Section 2.3)

Power Consumption

85 W continuous

Model Specific Information

Refer to the specification sheet for further technical and performance information required model:

•

•

•

•

•

Содержание ANDOR iKon-M






































Результаты поиска

Содержание ANDOR iKon-M

Отзывы:

Oxford Instruments ANDOR iKon-M, Руководство по оборудованию, Страница: 30 / 37

Результаты поиска

Содержание ANDOR iKon-M

Отзывы: