Oxford Instruments Andor Apogee Aspen Series страница 39 Скачать руководство пользователя

Страница: 39 / 45

Version 1.4 rev 23 Oct 2017

Aspen

9.5 f

ilTer

heel

nSTallaTion

This section outlines the filter wheel installation process (the images are shown for an Alta camera with a AFW50-9R) .
For dual filter wheel installations please contact your Andor representative for further information.

9.5.1 i

nSTalling

ilTerS

1. Set the Filter Wheel on clean flat surface and remove the two #10-32 x 7/16 buttonhead screws from the

mounting flange using the 1/8” Allen wrench provided.

2. Flip the Filter Wheel upside down and remove the two buttonhead screws from the back of the mounting

flange. Set aside the mounting flange and the four buttonhead screws for now.

3. Flip the Filter Wheel right side up and set it on the edge of a table. The motor should hang off the side so the

housing does not rock back and forth.

4. Remove the ten #6-32 x 5/16 flathead screws from the perimeter of the lid using the 5/64 Allen wrench

provided.

5. Remove the lid, making sure not to damage the light guard sticker of the connector face. Set aside the lid and

ten flathead screws for now.

6. Inspect for any packing materials or dust inside the wheel, remove using compressed air, optics brush or lens

tissue. (see Section 6 for general guidelines on the use of compressed air).

Содержание Andor Apogee Aspen Series














































Результаты поиска

Содержание Andor Apogee Aspen Series

Отзывы:

Похожие инструкции для Andor Apogee Aspen Series

Бренды по названию

Популярные бренды

Oxford Instruments Andor Apogee Aspen Series, Руководство по оборудованию

Результаты поиска

Содержание Andor Apogee Aspen Series

Отзывы:

Похожие инструкции для Andor Apogee Aspen Series

Бренды по названию

Популярные бренды