OXE OXE-150 HP Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 68

background image

24

OXE 150/200 HP INSTALLATION MANUAL

PROPELLER INSTALLATION

NOTE!

In twin, or more, installations, one propeller should be for right-hand

rotation and the other one should be for left-hand rotation. Both should be of the
same size (same diameter) and have the same pitch.

See Fig. 7 to 9 on previous

pages

.

!

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat
out of the water with a propeller installed. Before installing or removing a
propeller, place the drive unit in neutral and engage the lanyard stop switch
to prevent the engine from starting.

Fig. 11

Propeller shaft

1.

Apply marine grease according to table “Recommended Fluids and Grease”
to the propeller shaft before installing the propeller, as this will aid future
removal and corrosion resistance.

PROPELLER INSTALLATION

«
...
22
23
24
25
26
...
»

Содержание OXE-150 HP





































































Отзывы:

Нет отзывов

Похожие инструкции для OXE-150 HP

Бренд: TYAN Страницы: 82

tps61040EVM-002

Бренд: Texas Instruments Страницы: 31

Бренд: EPOX Страницы: 84

Бренд: Biostar Страницы: 115

Бренд: CHAINTECH Страницы: 49

Бренд: J&W Страницы: 42

Бренд: Intersil Страницы: 10

Бренд: u-blox Страницы: 24

Бренд: Intel Страницы: 91

Бренд: Texas Instruments Страницы: 18

MPG Z390 GAMING PLUS

Бренд: MSI Страницы: 76

Бренд: Zeal-All Страницы: 8

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 129

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 108

Бренд: ASROCK Страницы: 40

Бренд: Biostar Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды