Oxbox J951X D Series Скачать руководство пользователя страница 27

Страница: 27 / 44

Fault Conditions

There is a green and a red LED (labeled “Status”) on the

motor control board to provide system faults as described

below. Refer to

Table 14 (page 40)

to determine motor

control board fault conditions.

OPERATING SEQUENCE

The operating sequences for the heating, cooling, and fan

modes are described below. Refer to the field and furnace

wiring diagrams:

Heating Cycle

1. The thermostat calls for heat by energizing the

terminal

with 24VAC.

2. The control verifies the pressure switch is open.

3. If the pressure switch is open, the control energizes the

inducer and waits for the pressure switch to close. The

pressure switch must close within 10 seconds.

4. The control runs the inducer for a 30 second pre-purge.

5. The control energizes the Hot Surface Igniter (HSI) output

for the appropriate warm-up time limit.

6. The control energizes the main gas valve for 3 seconds.

7. If the flame proved and ignites the gas, the control de-

energizes the HSI. The gas valve and inducer remains

energized. The control goes to blower on delay.

8. If flame is present, the control energizes the blower on

the selected HEAT speed 30 seconds after the gas valve

opened. The gas valve and inducer remain energized.

9. When the thermostat demand for heat is satisfied, the

control de-energizes the gas valve. The Inducer output

remains on for a 30 second post-purge period.

10. Blower off timing begins when the thermostat is satisfied.

The control will operate at the selected HEAT speed of 60,

90, 120, or 180 seconds. If the blower off delay jumper is

not present, the fan should still operate for 120 seconds

at the selected HEAT speed. The Indoor blower motor

is de-energized after a blower off delay as selected by

the movable jumper.

Cooling Cycle

1. The thermostat calls for cooling by energizing the Y terminal

with 24VAC.

2. The control energizes the blower in cooling speed and

sends 24VAC to the contactor in the condensing unit

3. When the thermostat removes the call for cooling, the

contactor in the outdoor condensing unit is de-energized

and the control continues to run the fan for a period of 60

seconds.

Fan Mode

• When the thermostat energizes the

terminal for

continuous fan (without calling for heat or cooling), the

indoor fan is energized on the selected FAN speed. See

Figure 26 (page 24)

for fan speed settings.

• If a call for cooling occurs during continuous fan, the

blower will switch over to the selected COOL speed.

• If the

terminal receives a call for heat during continuous

fan, the blower will de energize.

• A call for fan is ignored while in lockout.

MAINTENANCE

WARNING:

ELECTRICAL SHOCK, FIRE OR

EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury, death or property

damage.
Improper servicing could result in dangerous

operation, serious injury, death or property

damage.
• Before servicing, disconnect all electrical

power to furnace.

• When servicing controls, label all wires prior

to disconnecting. Reconnect wires correctly.

• Verify proper operation after servicing.

• Proper maintenance is most important to achieve the best

performance from a furnace. Follow these instructions for

years of safe, trouble free operation.

• These maintenance instructions are primarily intended

to assist qualified technicians experienced in the proper

maintenance and operation of this appliance.

• Always reinstall the doors on the furnace after servicing.

Do not operate the furnace without all doors and

covers in place.

• Verify the thermostat is properly installed and will not be

affected by drafts or heat from lamps or other appliances.

• To achieve the best performance and minimize equipment

failure it is recommended that a yearly maintenance

checkup be performed. At a minimum, this check should

include the following items:

Air Filter(s) -

Air filter(s) are not supplied with the furnace as

shipped from the factory. The installer must provide a high

velocity filter that is appropriately sized to the return air duct

opening or external filter rack.

WARNING:

Never operate the furnace without a filter in place.

Dust and lint can build up on internal components,

resulting in loss of efficiency, equipment damage,

and possible fire.

It is recommended that filter(s) be 1” or 2” thick and be

cleaned or replaced monthly.
Filters designed to remove smaller particles such as pollen,

may require additional maintenance. Filters for side return

and bottom return applications are available from most local

distributors.

Blower Compartment -

Dirt and lint can create excessive

loads on the motor resulting in higher than normal operating

temperatures and shortened service life. It is recommended

that the blower compartment be cleaned of dirt or lint that

may have accumulated in the compartment or on the blower

and motor as part of the annual inspection.

Содержание J951X D Series













































Результаты поиска

Содержание J951X D Series

Отзывы:

Похожие инструкции для J951X D Series

Бренды по названию

Популярные бренды

Oxbox J951X D Series, Руководство по установке

Результаты поиска

Содержание J951X D Series

Отзывы:

Похожие инструкции для J951X D Series

Бренды по названию

Популярные бренды