Overland Storage LoaderXpress Скачать руководство пользователя страница 52

Страница: 52 / 104

3-2

Operation

RONT

ANEL

Figure 3–2 Control Panel Buttons

Using the Control Panel Buttons

To enter the Menu Mode and display the Main Menu from the Default Screen, press the

Enter

button.

Return to the Main Menu at any time from a submenu by pressing the

Escape

button

repeatedly until the Main Menu appears. Pressing the

Escape

button while the Main

Menu is displayed exits the Menu Mode and returns the LoaderXpress to the Default
Screen.

Table 3–1 Control Panel Buttons

Component

Description

Display Panel Screen

Backlit, 4-line by 20-character display, provides drive and loader
status, menu choices and error messages. Scrolls for more
information.

Buttons

Use to navigate through menu structure:

Escape -

Exit menus and submenus

Enter

- Select desired option

- Scroll up

- Scroll down.

LED Indicators

Ready

(green) – I

ndicates that the LoaderXpress is ready to accept

commands either from the Control Panel or the host. Goes out when
you enter Menu Mode

Use Cleaner

(yellow) - Drive requires cleaning.

Drive Fault

(red) - See Fault Screen for error condition or Fault

Symptom Code.

Loader Fault

(red) - See Fault Screen for error condition or Fault

Symptom Code.

Содержание LoaderXpress









































































































Результаты поиска

Содержание LoaderXpress

Отзывы:

Бренды по названию

Популярные бренды

Overland Storage LoaderXpress, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание LoaderXpress

Отзывы:

Бренды по названию

Популярные бренды