Overland Storage LoaderXpress Скачать руководство пользователя страница 32

Страница: 32 / 104

2-10

Installation

ACK

OUNT

NSTALLATION

APPLICABLE

)

CAUTION:

Rack mounted units are installed from the bottom due to the weight of

the unit when fully extended. An installed unit with empty spaces below that is fully

extended may cause the rack to tip forward or cause personal injury. It is
recommended that two persons support and slide the unit in the rack.

1) Locate the screw holes in the front and rear rails of the cabinet or equipment rack

where the library slides are to be installed.

Figure 2–13 Mounting Screw Locations

Figure 2–14 Rack Slide Mounting Holes

2) Locate the proper position (three holes above the top of the outer slide position)

for one clip nut behind the upper hole in each panel extension and the install 10-
32 clip nuts.

1 U is measured from the
center of one ½ inch space
to the center of the
next ½ inch space.

The Overland LoaderXpress
uses 4 U of rack space.

Hole spacing = 5/8 inch

1 U = 1.75 inches

Hole spacing = ½ inch

Hole spacing = 5/8 inch

1 U = 1.75 inches

Location of rails and
mounting hardware
for the LoaderXpress

Nut Clips

Slide rails and
Mounting Screws

4 U for
LoaderXpress

LXL-0069

Содержание LoaderXpress









































































































Результаты поиска

Содержание LoaderXpress

Отзывы:

Бренды по названию

Популярные бренды

Overland Storage LoaderXpress, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание LoaderXpress

Отзывы:

Бренды по названию

Популярные бренды