background image

Ins. No.

 

T-518-11-E

NONCONTACT PULSE GENERATORS

 

                                        MODEL PG30

/

PG30EP

MODEL  PG30

MODEL  PG30EP

GB type

Where pulses of scaled units or 
unscaled pulses are required

Pulse generator

for totalizer

LW13 type

CB type

PB type

Meter sizes 52 or 53; 
where pulses in scaled 
units are required.

If unscaled pulses 
uncompensated for 
temperature are re-
quired, it is mounted to 
the area encircled ( ○ ) 
of transmission gear 
box GB.

Equipped with regis-
ter Model LW11;where 
pulses of scaled units 
compensated for tem-
perature are required.

Equipped with regis-
ter Model LW42 or 
43;where pulses of 
scaled units com-
pensated for tem-
perature are required.

Pulse generator

for totalizer

 GENERAL

When used in conjunction with an OVAL flowmeter, the Model PG0/

PG0EP noncontact pulse generator provides voltage frequency pulses 

proportional to the flowrate of process fluid. Incorporated in the pulse 

generator are a premolded pulse generating element and a circuit 

which prevents false pulses otherwise generated by minute vibration 

of generator components. As the toothed disk rotates, a succession of 

voltage pulses (quasi rectangular wave) is generated. 
Generated pulses come either pulses in scaled units or unscaled 

pulses, depending on the position of flowmeter at which the generator 

is mounted. Pulses in scaled units can be used in remote totalizing, 

batching, blending systems and the like built around an OVAL flowmeter 

which serves as the sensing terminal. Unscaled pulses are converted 

into an analog signal for use in flow indicator/recorder/controller 

applications. Models PG0S/PG0SEP are compatible in the latter 

applications. 

 For complete details of Models PG0S/PG0SEP,see OVAL Products

    General Specifications GS No T-5-E.

Pulse generators come in the following two designs:

(1)Standard type

……

PG0

()Flameproof type

PG0EP (designed and fabricated according to the "Explosionproof Guide- 

lines" recommended by the Technology Institution of Industrial Safety.)

 Information about Models PG30S and PG30SEP appears in Instruction Manual No. T-523-E.

 PULSE GENERATOR INSTALLATION EXAMPLES

Generated pulses in scaled units

The rotor revolution is guided into gear reduction and instrumental 

error correction stages for the flowmeter to produce pulses of required scaled unit. The obtained pulse 

signal is used primarily for remote totalization. 

Содержание PG30











Отзывы: