Otto Bock Juvo Скачать руководство пользователя страница 100

99

Applying the attachment straps

1)  Hook  each  of  the  front  attachment  straps  into  its

corresponding  front  anchor  point  from  the  outside
(see fig. 99, left).

2)  Hook the rear attachment straps, 

2 x respectively

,

into the rear anchor points (see fig. 99, right).

3)  Tighten the front and rear attachment straps.

100

Securing the power wheelchair in the vehicle

1)  Position  the  power  wheelchair  in  the  vehicle  for

transporting  persons  with  reduced  mobility.  For
more information, refer to section 5 in the brochure
"Transporting  persons  with  reduced  mobility",
order number 646D158. 

2)  Turn the control device off (see Page 45). 
3)  Verify  brake  locking.  Engage  the  brakes  if  needed

(see Page 50).

4)  Apply the attachment straps (see below). 

101

Applying the attachment straps

1)  Hook  each  of  the  front  attachment  straps  into  its

corresponding  front  anchor  point  from  the  outside
(see fig. 101, left).

2)  Hook the rear attachment straps, 

2 x respectively

,

into the rear anchor points (see fig. 101, right).

3)  Tighten the front and rear attachment straps.

Placement of the restraint system integrated in the vehicle

Fastening the restraint lap belt of the vehicle for transporting persons with reduced mobility is mandatory.
The power wheelchair's lap belt should be used in addition to position the passenger during transportation.
The four-point belt can be used in addition to position the passenger during transportation.

6.18.3 Restrictions for use

WARNING

Risk of accidents and injury due to using the product with certain settings and/or installed options

Severe injury in case of accidents due to options coming loose

Before using the product as a seat in a vehicle for transporting persons with reduced mobility, remove options
that need to be taken off for safe transportation. Please observe the following table.

Stow all dismantled components securely in the vehicle for transporting persons with reduced mobility.

Please note that certain settings on  the product exclude the use of the  product in  a  vehicle for transporting
persons with reduced mobility.

100

Use

Juvo

Содержание Juvo





























































































































Отзывы: