LED Modern Crane Lamp
T57G5Z T5751Z T57G5B-FFP T5751B-FFP
PL-0064B
ENGLISH
LED Modern Crane Lamp
INS150163
REV052615
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
OttLite.com/warranty
LAMP ASSEMBLY
WARNING:
To prevent electrical shock, make sure the lamp is
not plugged in until fully assembled per instructions.
1.
Make sure the lamp is not plugged in to an electrical outlet.
2.
Remove all packing from the box and lay both lamp
assembly and base on a solid surface such as a table.
3.
Lift lamp assembly by lower arm (E) section and fully insert
dowel (D) into the stem (C) on the top of base (A).
4.
Insert lock screw (B) through the recessed hole located in
stem (C). Lock screw (B) can be tighten by hand turning
clockwise until snug.
NOTE: A screwdriver can also be
used to tighten lock screw (B).
5.
Connect power adapter input (O) into lamp cord connection (N).
6.
Plug power adapter (M) into a standard household 120V AC
outlet.
Note: Only use with supplied power adapter to
avoid damage or fire.
SAFETY WARNING:
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
LAMP OPERATION
1.
Turn the lamp ON or OFF by depressing switch (S) located
on the front-underside of the shade.
2.
To reposition the light, hold the base steady and grasp
either lower arm (E) or upper arm (F) to position as desired.
Lamp body can also rotate on base.
CAUTION:
The lamp is free to rotate on its base.
DO NOT
rotate the lamp such that the power cord begins to wind up.
3.
Shade (G) can rotate approximately 90 degrees left-right.
4.
To increase tension in arm joints, twist selected knobs
(H, K, L) clockwise by hand.
DO NOT
force knobs as they
can strip.
NOTE:
The important safety instructions appearing in
this instruction sheet are not meant to cover all possible
conditions and situations that may occur. It must be
understood that common sense, caution, and care must be
used with any electrical product.
CAUTION!
IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF
THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY
THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED
PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.
FCC PART 15
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that of the receiver.
•
Consult the dealer or an experienced radio/TV technician
for help.
CAUTION:
Any change or modification to product
not expressly recognized by OttLite Technologies voids
OttLite’s responsibility for proper function of product.
CAN ICES-3 (B) / NMB-3 (B)
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.2A
Output: 21.0V DC, 0.28A with a Male DC Plug
S
C
B
D
A
G
L
H
F
K
J
E
N
O
M
