Cool Breeze LED Fan Lamp
F26WGC F261GC F26WG9 F2600C F261G9 F26WG9-SHPR F261G9-SHPR
HSD9021B
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with your new
OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and return it today by
mail, or register online by going to: OttLite.com/warranty.
NOTE: THIS UNIT IS FULLY ASSEMBLED
1.
Remove lamp from packing placing lamp body base (A) flat on a steady
surface.
2.
Connect the AC Adapter input (H) into connector (J) in the bottom of the
lamp.
3.
Plug the AC adapter (G) into a standard household 120V AC outlet.
Note: Only
use with the supplied AC adapter to avoid damage or fire.
4.
This lamp provides three LED color modes, five levels of brightness and
three levels for fan speed.
5.
To power LED lighting, slightly touch switch (B) to achieve the following:
• to turn lamp “ON”; touch the switch “once”
• to turn lamp “OFF”; touch the switch a “second” time.
6.
Lamp includes 5 LED brightness settings. To adjust LED brightness settings,
slightly touch “
ˆ
” or “
ˇ
” arrows (C) located above and below power switch
(B). Upon turning ON lamp, it will initially set at the highest LED brightness
setting.
NOTE:
If dimmer function was employed prior to turning “OFF”
lamp, the lamp will return to lamp setting last employed unless disconnected
from adaptor.
7.
To adjust lighting color mode: touch “M” key (D) to switch light color
temperature mode; 4000°K, 5000°K, 2700°K.
NOTE:
4000°K is the default
color mode.
8.
To power fan, slightly touch fan switch (F) to turn “ON” and achieve the
following:
• for 1st fan speed setting; touch the switch “once”;
• for 2nd fan speed setting, touch the switch “twice”;
• for 3rd fan speed setting, touch switch “three-times”;
• to turn fan “OFF”; touch the switch “four” times.
9. NOTE:
The brightness of the fan status indicator light (E) will vary with the
current wind speed. The fan status indicator light is located on the inner
fan housing (N).
10.
To position shade (L) simply bend flex-neck (K) as needed to point the
light. Please hold the lamp base (A) while adjusting the lamp. Take care
not to overextend the lamp to avoid unbalancing it and damage. Please
refer to diagrams for lamp maximum adjustment range.
SAFETY WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
1.
Turn lamp off and
WAIT UNTIL LAMP HEAD (L) AND ADAPTER (G) ARE
COOL
before handling.
2.
LAMP HEAD (L) might get hot after several hours of continuous use,
DO
NOT
place your hands directly on the surface of lamp head.
3.
Never use with an extension cord unless the plug can be fully inserted into
the receptacles in the extension cord.
4.
Do not alter the plug.
5.
The lamp head included with this unit cannot be replaced by the consumer.
6.
INDOOR USE ONLY.
NOTE:
The important safety instructions appearing in this instruction sheet
are not meant to cover all possible conditions and situations that may occur. It
must be understood that common sense, caution, and care must be used with
any electrical product.
CAUTION NOTES
1.
THIS PRODUCT IS FOR INDOOR USE ONLY, DO NOT USE IN THE PRESENCE OF
FUMES IN THE ENVIRONMENT.
2.
SLIGHT NOISE IS NORMAL WHEN FAN IS RUNNING.
3.
DO NOT USE IN RAIN, MOISTURE; STAY AWAY FROM FLAMES, HOT
ENVIRONMENT, SO AS NOT TO DAMAGE THE PRODUCT.
4.
DO NOT COVER THE FAN INLET AND OUTLET.
5.
AFTER LONG USE OF PRODUCT OR PERIODIC USE, OPEN VENT COVER AND
REMOVE AND CLEAN FILTER OR REPLACE.
CAUTION!
IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE
IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS
SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.
INDOOR USE ONLY.
CAUTION!
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE;
WHENTHE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL
BE REPLACED.
CAUTION:
Any change or modification to product not expressly recognized
by OttLite Technologies voids OttLite’s responsibility for proper function of
product.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that of
the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
CAN ICES-005 (B)/NMB-005 (B)
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.5A
Output: 12V DC, 1A with a Male DC Plug
ENGLISH
Cool Breeze LED Fan Lamp
INS200592
REV072320
J
P
G
H
L
* Lamp cannot be used
in this position
Diagram 1
Diagram 2
120°
K
O
A
M
B
C
D
E
N
F
