CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with your
new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and return it
today by mail, or register online by going to: www.warranty.ottlite.com
LAMP ASSEMBLY
WARNING:
To prevent electric shock, make sure the lamp is not
plugged in until all assembly steps are complete.
This lamp includes an OttLite
®
Natural Daylight LED Bulb.
1.
Unpack all lamp parts and lay out on the floor with base (A)
laying flat.
2.
Thread pole (B) to base (A) by hand turning clockwise until tight.
3.
Thread upper pole (C) to lower pole (B) by hand turning
clockwise until tight.
4.
Thread arm (D) into upper pole (C) by hand turning clockwise
until tight. Pull excess cord along poles (B, C, D) and secure
within rubber rings (L).
5.
Attach shades (G) to socket housings (H) using socket rings (J)
to hold the shades in place.
6.
Thread socket rings (J) onto sockets by hand turning clockwise
until tight enough to hold the shades steady.
7.
Refer to BULB INSERTION/REMOVAL to install bulbs (K) in lamp.
8.
Plug the cord (D) into a standard 120V AC outlet.
9.
To turn the lamp
ON
or
OFF
press the switch (C).
10.
To adjust the direction of shades (G), grasp near socket housings
(H) and move the shades UP or DOWN until it reaches a stop.
DO NOT
force the shade into any position as damage may occur.
CAUTION:
As part of lamp design, there are three rubber rings (L) used
on poles (B, C, D) to keep cord (F) secured and to prevent tipping.
BULB INSERTION/REMOVAL
1.
Make sure that the lamp is not plugged into an electrical socket.
2.
If the lamp has been in use, allow it to cool approximately 5
minutes before proceeding.
3.
To install a bulb (K) in the socket, thread the base of the bulb into
the socket turning clockwise until snug.
CAUTION: DO NOT overtighten the bulb. Overtightening the
bulb may make removal difficult or damage the lamp or bulb.
4.
To remove a bulb (K) already installed in the lamp, unthread the
bulb from the socket turning counterclockwise to loosen.
SAFETY WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS
1. Turn off/unplug and WAIT UNTIL BULB IS COOL before handling.
2. Bulb gets hot quickly! Touch only switch/plug when turning
ON
or
OFF
.
3. Never use with an extension cord unless the plug can be fully
inserted into the receptacles in the extension cord.
4. Do not alter the plug.
NOTE: The important safety instructions appearing in this instruction
sheet are not meant to cover all possible conditions and situations that
may occur. It must be understood that common sense, caution, and
care must be used with any electrical product.
CAUTION!
IMPORTANT SAFETY INSTRUCTIONS: THIS PORTABLE LAMP HAS A
POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO REDUCE
THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY
ONE WAY. IF THE PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF
IT STILL DOES NOT FIT, CONTACT A QUALIFIED ELECTRICIAN. NEVER USE WITH AN
EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED. DO NOT ALTER THE PLUG.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
CAUTION!
IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE
IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS
SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.
INDOOR USE ONLY.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3 (B)
English
Avery Floor Lamp
INS-16-0289
REV101416
Avery Floor Lamp
L1A921G9-SHPR
FO587
E
L
F
J
A
H
G
H
D
G
K
C
L
K
B
J
