background image

 

 

15 

 

B. 

Testing Procedure

 

Using a regular otoscope or the delivery head with air flow turned off, 

examine the ear canal for the presence of cerumen and also to determine how 

best to direct the NCA-200 airstream.  The ear canal should be essentially 

free of cerumen.  If it is not, this must be removed prior to stimulating.  After 

selecting the proper temperature and the standard 60 second time for caloric 

stimulation, start the flow of air and then place the speculum of the otoscopic 

air delivery head directly into the ear and direct the flow of air onto the 

tympanic membrane.  

 

Momentarily depress the flow time activation trigger button on the delivery 

head.  If the NCA-200 is connected to the CHARTR 200 VNG/ENG or 

CHARTR VNG/ENG  system, subsequent depressions  of the flow time 

activation switch will center the tracing for VNG/ENG or start the video 

recording for VNG.  (If installed, the footswitch will also serve to start and 

center tracings or start the video recording.)  After the selected time interval 

has elapsed, a beep indicates when the otoscopic air delivery head should be 

removed.  After stimulation, remove the speculum from the ear, dispose of 

the speculum and carefully place the delivery head in a safe location.  Be sure 

to utilize alerting tasks as the eye movements are being recorded. 

Содержание ICS NCA-200



























Отзывы: