OSTBERG HERU 400-2400 S Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 120

OSTBERG HERU 400-2400 S Скачать руководство пользователя страница 22

22 / 120

Climatix HERU® 400-2400

2018-02-13

CONTROL SYSTEM Function description

Heat exchanger

Rotation monitor RV1 monitors the rotation of the rotary heat exchanger, EMS alarm
goes to HMI.
EMS has a built-in safety disconnection switch. In the event of over-current, an alarm is
sent from the heat exchanger to HMI. The alarm is reset on EMS (by unplugging mains
voltage/ext. switch disconnector) and on HMI. Alarm class selectable in HMI.

EHC

GT9 consists of a low-temperature alarm (automatic return) and a high-temperature
alarm (manual return). If the GT9 alarm is triggered, EHC will be blocked and cool
down will begin. The electric heating alarm can be reset in HMI. If the high
temperature protection has also tripped, GT9 must also be reset on the EHC electric
heater.
In the event of fire/smoke alarm, there will be no cool down of the EHC electric heater.
GP5 monitors minimum supply air flow/pressure. If pressure falls below the set value,
EHC is blocked and the alarm will not be sent.

Efficiency measurement extract air

Temperature efficiency is calculated via temperature sensors GT2, GT42 and GT3,
provided that the heat exchanger signal is 100%.
An alarm will go off if efficiency falls below the set value.

Fire/smoke

When a signal is received from the parent fire/smoke fume system, the fire/smoke
alarm will go off.
In the event of alarm, the following functions can be selected:
The unit is stopped and the damper closes.

•

Extract fan speeds up to the fire setpoint and supply fan is stopped. Dampers
ST1/ST2 remain open.

•

Supply fan speeds up to the fire setpoint and extract fan is stopped. Dampers
ST1/ST2 remain open.

•

Extract fans speed up to the fire setpoint. Dampers ST1/ST2 remain
open.

ALARM

Deviation alarm: GT1, GT2, GT3, GP1, GP2, GP3, GP4, GF1 AND GF2
Recovery alarm (rotor control EMS)
Fan alarm
frost protection sensor GT8/Overheating electric heater GT9
Low efficiency

Multifunctional input

The following functions are located on the same signal input and cannot be combined.

-

Control input 1: Timer input for additional speeds/

-

Control input 2: additional speeds from BMS.

-

Quick stop input

-

Common filter alarm, active via pressure sensor, supplied as optional accessory.

OPTION via add-on module EXP-1 (9050054)

The following functions are optional accessories and are not included in the basic
model supplied by H. Östberg AB.
In addition to the respective sensors, an EXP1 is also required to obtain multiple I/Os
(inputs/outputs).

«
...
20
21
22
23
24
...
»

Содержание HERU 400-2400 S

























































































































Отзывы:

Нет отзывов