iConverter
®
10GXT
Standalone Module User Manual
Product Overview
The iConverter 10GXT is a 10/100/1000BASE-T copper to 1000BASE-X or 10GBASE-R fiber
media converter, and is available as a compact, unmanaged standalone unit. The iConverter
10GXT supports jumbo frames up to 10,056 bytes. The 10GXT models are available with
SFP+ or XFP transceivers.
Installation Procedure
1) Configure DIP-switches
2) Install Standalone Module and Connect Cables
3) Verify Operation
1) CONFIGURE DIP-SWITCHES
DIP-SWITCH BANK 1
The location of the DIP-switches is shown in Figure 1.
The function of DIP-switch Bank is outlined in Figure 2.
Switch
Legend
Function
DOWN (Default)
UP
SW1
P1 AN/MAN
Port 1 Speed and Duplex
Auto
Manual
SW2
SW3
10G/1000
Port 2 Speed
10G
1000
SW4
P2 AN/MAN
Port 2 Negotiation
(1G Mode Only)
Auto
Manual
SW5
Link Modes
Asymmetrical Link Propagate
Port 1 to Port 2
Link Segment
Link Propagate
Port 1 to Port 2
SW6
Asymmetrical Link Propagate
Port 2 to Port 1
Link Segment
Link Propagate
Port 2 to Port 1
Figure 2: DIP-switch Definitions
3) VERIFY OPERATION
Once the module has been installed and configured per steps 1 and 2, verify the module is
operational by viewing the LED indicators.
LED Function
“Legend”
Color
OFF State
ON/Blinking State
Power
“PWR”
Green
No power
Solid Green:
Module has power
P1 Negotiation Mode
“AN”
Green
Port is configured for Manual
operation
Solid Green:
Port is configured for auto-
negotiation
Blinking Green:
Port is configured for
auto-negotiation but has not completed
the process with attached link partner
P1 Link Activity
“100”
Green
Port not linked at 100M
Solid Green:
Port linked at 100M
Blinking Green:
Data activity
P1 Link Activity
“1000”
Green
Port not linked at 1000M
Solid Green:
Port linked at 1000M
Blinking Green:
Data activity
P1 Link Activity
“100” and “1000”
Green
Port not linked at 10M
Solid Green:
Port linked at 10M
Blinking Green:
Data activity
P1 Duplex
“FDX”
Green
Port is configured for half
duplex per DIP-switch or
resolved by auto-negotiation
Solid Green:
Port is configured for
full duplex operation per DIP-switch or
resolved by auto-negotiation
P2 Speed
“P2 1000”
(SFP+ Model Only)
Green/
Amber
Port not linked at 1000M
Solid Green:
Port linked at 1000M
Blinking Green:
Data activity
Blinking Amber:
Port is operating at
1000M and receiving a remote fault
P2 Speed
“10G”
Green
Port not linked at 10G
Solid Green:
Port linked at 10G
Blinking Green:
Data activity
P2 FDX
Green
Port is has negotiated to
half duplex or port has not
established a link
Solid Green:
Port is negotiated to full
duplex operation by auto-negotiation
P2 DDMI
“Stats”
Green/
Amber
Transceiver does not support
digital diagnostic or no
transceiver is installed
Green Solid:
Transceiver supports
digital diagnostic and no DDMI alarm
detected
Amber Solid:
Transceiver supports
digital diagnostic and DDMI alarm
detected
Figure 5: LED Indicators
LED Legend/State
Link Speed
“1000”
“100”
OFF
OFF
Port not linked
OFF
ON
Port linked at 100Mbps
ON
OFF
Port linked at 1000Mbps
ON
ON
Port linked at 10Mbps
Figure 6: Port 1 Speed LED Indicators
040-08580-001A 1/16
Page 1
Omnitron Systems Technology * 38 Tesla, * Irvine, CA 92618
949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com
©2016 Omnitron Systems Technology, Inc. iConverter is a registered trademark of Omnitron Systems Technology, Inc.
Trademarks are owned by their respective companies. Specifications subject to change without notice. All rights reserved.