Ossa Explorer страница 49 Скачать руководство пользователя

Страница: 49 / 70

User manual 49

Storage

Storage

If the motorcycle is to be stored for a long period of time, the fo-
llowing procedure should be followed to ensure that it is stored co-
rrectly.

- Clean the motorcycle as much as possible because dirt

can cause the deterioration of components.

-Turn on the engine for a few minutes to warm up the

transmission fluid and then drain. (see section on draining fluid).

-Fill up with new transmission fluid.

-Empty the fuel tank (petrol degrades over time).

-Lubricate the chain and all wires.

-Apply oil to non-painted metal surfaces to prevent rust.

Avoid putting oil on the brakes and rubber parts.

-Wrap the outside of the exhaust pipe in a plastic bag to

prevent rust.

-Position the motorcycle so that the wheels don’t touch

the ground to prevent possible tyre deformation. If this is not possi-
ble, cardboard can be placed underneath the wheels.

-Place a cover over the motorcycle such as canvas, plastic

or material. This will protect the motorcycle from dust and other
external factors. Avoid storing the motorcycle outside, or in direct
sunlight.

Starting the motorcycle again

To start up the motorcycle after a period of inactivity, the following
procedure should be followed:

-Remove the plastic covers that were placed over the mo-

torcycle before storing, including the exhaust pipe and those parts
that had special protection.

-Tighten the sparkplug.

-Fill up the fuel tank with new petrol.

-Carry out general lubrication.

-Check tyre pressure.

-Leave the engine running for some minutes to warm up

the engine oil.

Содержание Explorer







































































Результаты поиска

Содержание Explorer

Отзывы:

Похожие инструкции для Explorer

Бренды по названию

Популярные бренды

Ossa Explorer, Руководство пользователя

Результаты поиска

Содержание Explorer

Отзывы:

Похожие инструкции для Explorer

Бренды по названию

Популярные бренды