manualshive.com logo in svg

Oshkosh JLG 400S, Руководство по обслуживанию и ремонту

Поделиться
Скачать
Oshkosh JLG 400S Скачать руководство пользователя страница 382

SECTION 6 - JLG CONTROL SYSTEM (S/N 61718 TO PRESENT)

6-66

– JLG Lift –

3120895

Table 6-7. System Test Messages

Message Displayed on

Analyzer

Message Displayed on

Analyzer

Description

RUNNING

Initial display when system test is run; certain “critical” checks are made. Prob-
lems that can be reported include below messages.

ONLY 1 ANALYZER!

Do not connect two Analyzers while running the system test.

BATTERY TOO LOW

The system test cannot run with battery voltage below minimum (9 V).

BATTERY TOO HIGH

The system test cannot run with battery voltage above maximum. (16 V).

CHECK CAN WIRING

The system test cannot run in platform mode unless data is being received from 
the platform and ground modules. The system test cannot run in ground mode 
unless data is being received from the platform module.

CHECK SPEED

There is an open- or short- circuit in the speed encoder wiring. Check speed 
encoder.

BAD GROUND MODULE

An internal problem was detected in the ground module.

HIGH TILT ANGLE

The vehicle is very tilted (19.3 ), or the tilt sensor has been damaged. Check tilt 
sensor.

HOT ENGINE 

The engine temperature exceeds 100

C. This is only a warning.

BAD I/O PORTS

The controller detected a problem with its internal circuits at switch on. If other 
problems are also detected, the controller may need replacing.

SUSPECT EEPROM

The controller detected a problem with its EEPROM stored personality settings at 
switch on. Check and, if necessary correct, all personality settings.

OPEN FSW

In platform mode, the footswitch must be open at the start of the test.

CLOSE FSW

In platform mode, the footswitch must be closed when this message is displayed; 
the footswitch MUST BE KEPT CLOSED during the valve & contactor tests.

BAD FSW

The two footswitch signals are not changing together, probably because one is 
open-circuit. One footswitch signal (“FSW1”) is routed to the power module, the 
other (“FSW2”) is routed to the platform module. Check footswitch and wiring.

Содержание JLG 400S















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды