Orthman 125-087-02-EN-OM Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 62

Orthman 125-087-02-EN-OM Скачать руководство пользователя страница 19

SAFETY INFORMATION

DR12x2 Row Hopper Planter OM-EN

2-11

Orthman Left Side Decals

NOTE:

The 36 in row spacing planter is shown. The 38 in

row spacing planter and 40 in row spacing planter
are similar.

ORM000118

Figure 2-5

C A U T I O N

1. Read and understand all operator manuals before implement use.
2. Follow all tractor or towing device operating procedures and safety guidelines.
3. Do not allow riders on implement.
4. Lower implement to the ground, place tractor in park, turn off engine, and remove key.
Wait for all moving parts to come to a complete stop before working on implement.
5. Be extremely careful working around unshielded sharp edges.
6. Make sure all safety lighting and decals are clean. Use hazard lights when in transport.
7. Engage all safety devices before transporting or working beneath implement.
8. Contact or close proximity to power lines can result in electrocution.
9. Review all safety instructions with all operators on a frequent basis.

«
...
17
18
19
20
21
...
»

Содержание 125-087-02-EN-OM































































Отзывы:

Нет отзывов