Orolia KANNAD 406 AF Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 60

Orolia KANNAD 406 AF Скачать руководство пользователя страница 38

PAGE: 208

MAR 30/2020

INSTALLATION MANUAL OPERATION MANUAL

KANNAD 406 AF / AF-H / AF (6D)

© 2020 Orolia S.A.S. All rigths are strictly reserved.

C. ELT installation

• Verify that the ELT identification label matches the aircraft tail number.
• Mount the transmitter on the bracket.
• Slide the self-stripping strap thought the buckle and fasten it tightly.

Figure 206: Installing the transmitter on the bracket

CAUTION:

AN INCORRECT TIGHTENING OF THE HOOK AND LOOP
FASTENER COULD LEAD TO AN UNSAFE SITUATION BY THE ELT
PREVENTING THE TRANSMISSION OF THE DISTRESS MESSAGE

IMPORTANT:

Once installed in the mounting bracket, the installer must be sure
that the transmitter is firmly attached in its bracket by trying to
extract it manually, thereby verifying there is no play and that it
remains attached when extraction from the bracket is attempted.

• Connect the external antenna to the BNC connector (

Refer to Figure 207:

Installation, controls and connectors

Figure 2: ELT system

description page 3

NOTE regarding the external antenna: The specific installation
(tightening torque, etc.) of the external antenna is not covered by this
manual. Refer to antenna manufacturer's instructions. General
instructions for an external antenna installation are detailed

3. Antenna Installation page 209

• Connect the Remote Control Panel (or CS144) to the DIN12 connector

Refer to Figure 207: Installation, controls and connectors

) as shown

Figure 2: ELT system description page 3

CAUTION: WHEN ACTIONING THE ARM/OFF/ON SWITCH, PULL LEVER
TO UNLOCK AND SET TO POSITION.

«
...
36
37
38
39
40
...
»

Содержание KANNAD 406 AF





























































Отзывы:

Нет отзывов