Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 41 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

Recommended sequence of operations

5.5.2. Spring charge and actuating levers

The actuating and spring charge levers to be used to drive

the switch-disconnector-earthing switch of the circuit-

breaker function with AV/RAV driving mechanisms are:

Figure 5.19.

Switch-disconnector actuating lever

Figure 5.20.

Spring charge lever

5.5.3. Opening operation from earthing position

Initial conditions:

earthing switch closed and circuit-

breaker closed.

Move the access handle in the yellow zone to its bottom

position.

Figure 5.21.

Earthing switch driving shaft access handle detail.

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды