Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 18 / 76

IG-308-EN version 01; 03/06/2022

Installation

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

4.4.1. Cubicles with internal arc classification IAC up to 25 kA - 1 s

[7]

In each case, bear in mind which cable is to be used in the installation.

Feeder and cable rise function

Front and rear cable input or output (D1)
Side cable input or output (D2)

Figure 4.3.

Dimensions [mm] of the cable trench for

cgm

.3-huv-l

and

cgm

.3-huv-rc

Trench necessary for the feeder and cable rise function

Cable details

Approximate

radius of

curvature*

[mm]

Minimum depth

Cable insulation

Cable type

Cable

section

[mm

]

Cable

diameter

[mm]

D1 [mm]

D2 [mm]

eigh

1400 mm***

Dry insulation

One-core 18/30 kV

< 150**

555

500

800

185

590

550

900

240

45.2

640

300

47.5

685

650

1000

400

745

Three-core 18/30

< 150

92.7

805

950

eigh

1745 mm

Dry insulation

One-core 18/30 kV

< 150**

555

370

500

185

590

370

550

240

45.2

640

300

47.5

685

370

660

400

745

Three-core 18/30

< 150

92.7

805

650

* Check against the data of the manufacturer of the cable used.
** 150 mm

cable valid up to 21 kA.

*** Exclusively for -l cubicles.

Table 4.2.

Trench necessary for the feeder and cable rise function

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды