Orion ORION 8002 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 21

background image

Tri-Mode Three Channel Configuration

●

Lowest recommended impedance is 2

W

stereo and 4

W

bridged mono.

●

Stereo operation must be used.

●

Outputs must be configured for full range operation.

●

Output is configured stereo and summed bridged.

●

Passive crossover frequencies must not overlap.

WARNING!

Failure to do so may result in damage to the amplifier.

12

©2004 Directed Electronics, Inc.

«
...
11
12
13
14
15
...
»

Содержание ORION 8002






















Отзывы:

Нет отзывов

Похожие инструкции для ORION 8002

Бренд: DAPAudio Страницы: 13

Бренд: DAPAudio Страницы: 18

Бренд: DAPAudio Страницы: 18

Palladium P-400

Бренд: DAPAudio Страницы: 18

Бренд: DAPAudio Страницы: 16

EVO PHONODAC TWO

Бренд: M2TECH Страницы: 2

Бренд: Positron Страницы: 44

Бренд: Ace Plus Страницы: 11

Бренд: icon Audio Страницы: 10

Бренд: Teac Страницы: 48

Бренд: Saluki Страницы: 85

Бренд: JL Audio Страницы: 13

Бренд: B2 Audio Страницы: 10

Бренд: AvidHiFi Страницы: 16

Бренд: Rane Страницы: 16

Бренд: Rolls Страницы: 4

Бренд: Ma Audio Страницы: 23

Бренд: Chandler Limited Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды