ORiNG TRGPS-9084GT-M12X-BP2-MV Скачать руководство пользователя страница 6

Страница: 6 / 178

TRGPS-9084GT-M12X-BP2-MV User

Manual

ORing Industrial Networking Corp

Authentication and Accounting Server Status

.......................................................... 119

Authentication and Accounting Server Statistics

..................................................... 121

5.8.6

NAS (802.1x)

......................................................................................................... 123

5.9

Alerts ............................................................................................................................ 133

5.9.1

Fault Alarm

............................................................................................................ 133

5.9.2

System Warning

.................................................................................................. 134

5.10

Monitor and Diag .......................................................................................................... 137

5.10.1

MAC Table

........................................................................................................ 137

5.10.2

Port Statistics

.................................................................................................. 140

5.10.3

Port Mirroring

.................................................................................................. 142

5.10.4

System Log Information

............................................................................... 143

5.10.5

Cable Diagnostics

.......................................................................................... 144

5.10.6

SFP Monitor

..................................................................................................... 145

5.10.7

Ping

.................................................................................................................... 146

IPv6 Ping

.............................................................................................................................. 147

5.11

Synchronization ............................................................................................................ 147

5.12

PoE ............................................................................................................................... 149

5.12.1

Configurations

................................................................................................ 149

5.12.2

Status

................................................................................................................. 152

5.12.3

PoE Schedule

.................................................................................................. 153

5.12.4

PoE Auto-Ping

................................................................................................. 153

5.13

Troubleshooting ............................................................................................................ 154

5.13.1

Factory Defaults ....................................................................................................... 154

5.13.2

System Reboot ......................................................................................................... 155

Command Line Management .................................................................... 156

Содержание TRGPS-9084GT-M12X-BP2-MV



















































































































































































Результаты поиска

Содержание TRGPS-9084GT-M12X-BP2-MV

Отзывы:

Бренды по названию

Популярные бренды

ORiNG TRGPS-9084GT-M12X-BP2-MV, Руководство пользователя

Результаты поиска

Содержание TRGPS-9084GT-M12X-BP2-MV

Отзывы:

Бренды по названию

Популярные бренды