manualshive.com logo in svg

ORiNG TRGPS-9084GT-M12X-BP2-MV, Руководство пользователя

Поделиться
Скачать
ORiNG TRGPS-9084GT-M12X-BP2-MV Скачать руководство пользователя страница 27

 

TRGPS-9084GT-M12X-BP2-MV  User

 

Manual 

 

ORing Industrial Networking Corp 

26 

and provide network redundancy. Network loops occur frequently in large networks as when 

two or more paths run to the same destination, broadcast packets may get in to an infinite loop 

and hence causing congestion in the network. STP can identify the best path to the destination, 

and block all other paths. The blocked links will stay connected  but  inactive. When the best 

path fails, the blocked links will be activated. Compared to STP which recovers a link in 30 to 

50 seconds, RSTP can shorten the time to 5 to 6 seconds. 

 

STP Bridge Status   

This page shows the status for all STP bridge instance.   

 

 

Label 

Description 

MSTI 

The  bridge  instances.  You can also  link to the STP detailed 

bridge status. 

Bridge ID 

The bridge ID of this bridge instance. 

Root ID 

The bridge ID of the currently selected root bridge. 

Root Port 

The switch port currently assigned the root port role. 

Root Cost 

Root path cost. For a root bridge, this is zero. For other bridges, 

it is the sum of port path costs on the least cost path to the Root 

Bridge. 

Topology Flag 

The current state of the  Topology Change Flag for the bridge 

instance. 

Topology Change Last 

The time since last Topology Change occurred. 

Refresh 

Click to refresh the page immediately. 

Auto-refresh 

Check this box to enable an automatic refresh of the page at 

regular intervals. 

 

 

 

 

 

 

 

Содержание TRGPS-9084GT-M12X-BP2-MV



















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды