Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
The
series, including the
and
are managed Ethernet switches designed for
industrial applications, such as rolling stock, vehicle, and railway
applications. The switches boast EN50155 compliance and M12
connectors to ensure tight and robust connections, and guarantee
reliable operation against environmental disturbances, such as vibration and
shock. All models feature eight 10/100Base-T(X) P.S.E. ports which are able
to provide sufficient power for power-hungry devices. Therefore, you can
attach an IEEE 802.3af-compliant device to the switch without requiring
additional power. The devices also provide 1 set of bypass ports that ensure
constant network connectivity if power outage or node failure occurs. In such
situations, the device will bypass the inactive switch and continue to transfer
network traffic to the next switch in the relay.
TPS-3882GT-M12-BP1
TPS-3882GT-M12-BP1
TPS-3882GT-M12-BP1-24V
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Hold the
evice upright against the wall
Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Slide the
evice downwards and tighten the four screws for added stability.
Step 1:
Step 2:
Step 3:
d
d
The
series is shipped with the following items. If any
of these items is missing or damaged, please contact your customer service
representative for assistance.
TPS-3882GT-M12-BP1
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TPS-3882GT-M12-BP1/
TPS-3882GT-M12-BP1-24V
Pictures
Number
1
CD
1
Dimension
Panel Layouts
Front View
1. Reset button
2. Power1 status LED
3. Power2 status LED
4. R.M. status LED
5. Ring status LED
6. Fault LED
7. Relay output port
8. Console port
9. Power connector
10. PoE fast Ethernet ports (P1~P8)
11. LNK/ACT indicator for PoE Fast Ethernet
port
12. PoE status LED for PoE Fast Ethernet
ports
13. Duplex/collision indicator for
PoE Fast Ethernet port
14. Fast Ethernet Ports (P9 ~ P16)
15.
16.
17. Gigabit Ethernet port
18.
indicator for Gigabit Ethernet
ports
19. 100Mbps indicator for Gigabit Ethernet
ports
LNK/ACT indicator for Ethernet ports
Duplex/collision status LED for
Ethernet ports
LNK/ACT
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for the dual power inputs.
Insert a power cable to the power connector on the device.
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Step 1:
Step 2:
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay
N.C.
3A@24VDC
Network Connection
The switch has sixteen 10/100Base-T(X) and two 10/100/1000Base-T(X) Ethernet ports in the form
of M12 connector. Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to
connect to network devices (PCs, servers, switches, routers, or hubs). Please refer to the
following table for cable specifications.
4-Pin Fast Ethernet Port Definition
TPS-3882GT-M12-BP1
TPS-3882GT-M12-BP1
1907-2-29-TPS3882GTBP1-1.0
Switch
EN50155
EN50155 18-port managed
PoE Ethernet switch
I N D U S T R I A L
1
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
The switch uses the M12 A-coded 5-pin male connector on
the front panel for relay output. Use a power cord with an
M12 A-coded 5-pin female connector to connect the relay.
The relay contacts will detect user-configured events and
form an open circuit when an event is triggered.
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
4-pin female M12
D-coding connector
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
4-pin female M12
D-coding connector
1000BASE-T
Cat. 5/Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
8-pin female M12
A-coding connector
For pin assignments of the LAN ports, please refer to the following tables.
QIG
1
2
Tx+
1
Rx+
Tx-
4
Rx-
3
8-Pin Gigabit Port Definition
M12 Pin Description
Pin No.
Description
#1
BI_DC+
#2
BI_DD+
#3
BI_DD-
#4
BI_DA-
#5
BI_DB+
#6
BI_DA+
#7
BI_DC-
#8
BI_DB-
7
8
9
11
13
19
18
17
Console port pinouts
N.C.
RXD
RS-232, 9600bps, 8, N, 1
GND
TXD
N.C.
4
5
6
7
8
2
1
3
Fault
Ring
R.M.
PWR2
PWR1
Reset
3A@24VDC
Relay
N.C.
Relay Output
Console
N.C.
RXD
RS-232, 9600bps, 8, N, 1
GND
TXD
N.C.
Power
P1
LNK/ACT
DPX/COL
P2
LNK/ACT
DPX/COL
P3
LNK/ACT
DPX/COL
P4
LNK/ACT
DPX/COL
P9
LNK/ACT
DPX/COL
P10
LNK/ACT
DPX/COL
P11
LNK/ACT
DPX/COL
P12
LNK/ACT
DPX/COL
P5
P6
P7
P8
P13
P14
P15
P16
V1+
V1-
V2+
V2-
G2
LNK/ACT
100M
G1
LNK/ACT
100M
Power
Failure
Bypass
4
5
6
7
8
2
1
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
3
TPS-3882GT-M12-BP1
PoE
PoE
PoE
PoE
Fault
Ring
R.M.
PWR2
PWR1
Reset
3A@24VDC
Relay
N.C.
Relay Output
Console
N.C.
RXD
RS-232, 9600bps, 8, N, 1
GND
TXD
N.C.
Power
P1
LNK/ACT
DPX/COL
P2
LNK/ACT
DPX/COL
P3
LNK/ACT
DPX/COL
P4
LNK/ACT
DPX/COL
P9
LNK/ACT
DPX/COL
P10
LNK/ACT
DPX/COL
P11
LNK/ACT
DPX/COL
P12
LNK/ACT
DPX/COL
P5
P6
P7
P8
P13
P14
P15
P16
V1+
V1-
V2+
V2-
G2
LNK/ACT
100M
G1
LNK/ACT
100M
Power
Failure
Bypass
4
5
6
7
8
2
1
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
3
TPS-3882GT-M12-BP1
PoE
PoE
PoE
PoE
10
12
14 15
16
4 5 6
2 3
Pin No.
Description
#1
TD+ power input +
#2
TD- power input +
#3
RD+ power input -
#4
RD- PoE power input -
Tx+
Rx+
Tx-
Rx-
Tx+: PoE Vout+
Tx- : PoE Vout+
Rx+: PoE Vout-
Rx- : PoE Vout-
P1~P8
Tx+
Rx+
Tx-
Rx-
P9~P16
Tx+
Rx+
Tx-
Rx-
Tx+: PoE Vout+
Tx- : PoE Vout+
Rx+: PoE Vout-
Rx- : PoE Vout-
P1~P8
Tx+
Rx+
Tx-
Rx-
P9~P16
Pin No.
PoE Port Description
Non-PoE Port Description
#1
RD+ with PoE power input -
RD+ power input -
#2
TD+ with PoE power input +
TD+ power input +
#3
RD- with PoE power input -
RD- power input -
#4
TD- with PoE power input +
TD- power input +
